Replacement of carbon brush (Fig D)
- Remove the carbon brush lid (6) with a screw-
driver.
- Replace the carbon brush.
- Install the carbon brush lid (6) with a screwdriver.
Use:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- Assemble the sanding Sheet
- Turn the appliance on, by using the on/off button
(1).
- Place the appliance against the surface you want
to work.
- Slowly move the appliance over the workpiece,
- Do not apply excessive pressure against the work-
piece.
- Apply uniform sanding pressure against the work-
piece to increase performance and working life of
the sander and the sanding sheet.
Once you have finished using the appliance:
- Stop the appliance using the on/off switch (1).
- Unplug the appliance from the mains.
- Clean the appliance.
Cleaning
-
Disconnect the appliance from the mains and al-
low it to cool before undertaking any cleaning task.
- Allow it to cool before undertaking any cleaning
task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT IM-
MERSE IN WATER OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products, for
cleaning the appliance.
- Do not let water or any other liquid get into the
air vents to avoid damage to the inner parts of the
appliance.
- Never submerge the appliance in water or any
other liquid or place it under running water.
- If the appliance is not in good condition of cleanli-
ness, its surface may degrade and inexorably affect
the duration of the appliance’s useful life and could
become unsafe to use.
Supplies
- Always use original supplies, designed specifically
for your appliance model.
- These supplies are available in specialist shops.
6
- Do not use the appliance if the accessories or con-
sumables attached to it are defective. Replace them
immediately.
- Disconnect the appliance from the mains when not
in use and before undertaking any cleaning task.
- Unplug the appliance from the mains before replac-
ing any accessory.
- This appliance is for professional use.
- This appliance is intended for adult use. Ensure that
this product is not used by the disabled, children or
people unused to its handling.
- This appliance is not a toy. Children should be su-
pervised to ensure that they do not play with the ap-
pliance.
- Do not expose the appliance to extreme tempera-
tures.
- Keep the appliance in a dry, dust-free place, out of
direct sunlight.
- Always check the workpiece before operation and
remove any obstructions such as nails, staples,
screws, string, rags, cloths and other debris.
- Never rest the appliance into a surface while in use.
- Do not use the appliance on any part of the body of
a person or animal.
- Let the appliance running with no load for 30 sec-
onds in a safe position. If you notice serious vibration
or other defects stop the appliance immediately. Then
check the problem and /or proceed as we describe on
Anomalies and Repair clause.
Product description and Specifications
Description (Fig. A, B, C, D, E)
1- On/Off Switch
2- Locking button
3- Speed dial adjustment
4- Rear handle
5- Lateral handle
6- Carbon brush lid
7- Pad cover
8- Viscid disc
9- Sand Paper
10- Lid
11- Knob
12- Dust outlet
Instructions for use
Before use:
- Make sure that all the product’s packaging has been
removed.
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the ap-
pliance.
Sand paper Replacement (Fig B)
- To remove the sand paper (9) grasp it and pull it off
from the Viscid disc (8).
- Pay attention that punched holes of the sand paper
(9) match with the holes of the Viscid disc (8).
- Position the sand paper (9) flush alongside one edge
of the Viscid disc (8).
- Lay the sand paper (9) onto the Viscid disc (8) and
press firmly.
- To remove the sand paper (9) grasp it and pull it off
from the Viscid disc (8).
Replacement of Viscid disc (Fig B)
- Remove the sand paper (9).
- Block the rotation of the viscid disc (8)
- Put the allen wrench in to the hexagon hole in the
center of the viscid disc (8)
- Rotate the allen wrench clockwise
- Remove the old viscid disc (8)
- Install the new viscid disc (9)
Electronic speed control (Fig A)
- The speed of the appliance can be regulated by
using the speed regulator control (3). This function
is very useful, as it makes it possible to adapt the
speed of the appliance to the type of work that needs
to be done.
Switch on y Switch off (Fig A)
- Turn the appliance on, by pushing the on/off but-
ton (1)
- To activate the self-locking switch press the locking
button (2) while holding down the on/off button (1).
- To turn the appliance off, press the on/off button (1)
without pressing the locking button (2)
Sanding the corner (Fig C)
- Disassemble the removable lid (10) from the pad
cover (7)
- Rotate the adjust knob (11) anti-clockwise.
- Rotate the pad cover (7) until the desired position.
- Rotate the adjust knob (11) clockwise.
- Sand the corner space.
Connection set for dust outlet (Fig E)
- Connect the dust hose (13) into the dust outlet 12
- Rotate the dust hose (13) clockwise in order to lock
it
- Attach the cloth bag (14) to the dust hose (13)
