background image

Installing the UPC Open 

 

 

 

UPC Open 

Carrier Proprietary and Confidential 

CARRIER CORPORATION ©2017   

Installation and Integration Guide 

 

All rights reserved 

 

 

 

Wiring specifications for BACnet MS/TP and ARC156 

  

Cable: 

22 AWG or 24 AWG, low-capacitance, twisted, stranded, shielded copper wire 

Maximum length: 

2000 feet (610 meters) 

 

 

WARNING

  Do not apply line voltage (mains voltage) to the controller's ports and terminals. 

 
 
 

 

To wire the controller to the BACnet network 

Pull the screw terminal connector from the controller's power terminals labeled 

Gnd 

and 

Hot

Check the communications wiring for shorts and grounds. 

Connect the communications wiring to the controller’s screw terminals labeled 

Net +

Net -

, and 

Shield

.  

NOTE  

Use the same polarity throughout the network segment. 

Set the communication type and baud rate. 

  

 

 

For...

 

 

 

Set DIP switches 1 and 2 

to...

 

 

DIP switch 3

 

 

Set DIP switch 4 

to...

 

 

Set DIP switches 5 through 8 to...

 

MS/TP (m) 

The appropriate baud 

rate. See the 

MS/TP 

Baud 

diagram on the 

controller. 

N/A 

On 

Off/Off/Off/Off 

ARC156 

N/A. Baud rate will be 

156 kbps regardless of 

the DIP switch settings. 

N/A 

Off 

N/A 

   

NOTE

  Use the same baud rate for all controllers on the network segment. 

 

For MS/TP, verify that the EIA-485 jumpers are set to EIA-485 and 2w. 

Wire the controllers on a BACnet MS/TP or BACnet ARC156 network segment in a daisy-chain configuration. 

If the UPC Open is at either end of a network segment, connect a BT485 to the UPC Open. 

Insert the power screw terminal connector into the UPC Open's power terminals. 

Verify communication with the network by viewing a Module Status report in the i-Vu® interface.  

 
 
 

 

Содержание UPC Open































Отзывы: