background image

Start-up 

 

 

 

UPC Open 

Carrier Proprietary and Confidential 

CARRIER CORPORATION ©2017   

Installation and Integration Guide 

 

All rights reserved 

 

14 

 

Use one of the following interfaces to start up, access information, read sensor values, and test the controller. 
 

This interface...

 

Provides a...

 

Field Assistant 

application - 

Runs on a laptop that connects to controller's Local Access port 

1

 

Temporary interface 

Equipment Touch

 device - 

Connects to controller's Rnet port

 2

 

Temporary or permanent 

interface  

i-Vu®

 application 

Available for BACnet systems only  

Permanent interface 

System Touch

 device  

Available only for BACnet MS/TP systems.  

Wire to a BACnet MS/TP network connector and a 24 Vac power supply 

3

 

Temporary or permanent 

interface  

1

  Requires a USB Link (Part #USB-L). 

2

  See the 

Equipment Touch Installation and Setup Guide

 for detailed instructions. 

3

  See the 

System Touch Installation and Setup Guide

 for detailed instructions. 

 

CAUTION

   If multiple controllers share power but polarity was not maintained when they were wired, the 

difference between the controller's ground and the computer's AC power ground could damage the USB Link and 

the controller. If you are not sure of the wiring polarity, use a USB isolator between the computer and the USB 

Link. Purchase a USB isolator online from a third-party manufacturer.  

 
 

 

Select or create a custom control program and graphic for the UPC Open 

The field-installed UPC Open does not come from the factory with a control program or graphic. You must load a 

control program and graphic as part of the installation/commissioning of the UPC Open.  You can select a control 

program and graphic from EquipmentBuilder that has all the configurations that are currently available on a 

factory-installed UPC Open. You can also create a custom control program using Snap. See Snap Help for details.  
 

NOTES

 

 

You MUST have installed the February 2017 or later cumulative update and the 6.04.xxx or later driver to be 

able to create custom control programs, .view files, or .touch files for the ZS sensors, wireless sensors, or 

touchscreen. 

 

Third party mapping information for current Carrier PIC products, whether on a factory-installed UPC Open or 

selected from EquipmentBuilder, can be found on the 

Carrier Control Systems Support Site

 

http://www.hvacpartners.com/

 under 

Support Center 

Controls Support

 > 

Controls Product Information

 
 
 
 

Start-up 

Содержание UPC Open































Отзывы: