Carrier TRANSICOLD 69NT20-274 Скачать руководство пользователя

Страница: 53 / 182

4-7

against the cylinder deck (middle bowed away from

cylinder deck). Use new gaskets when reinstalling valve

plates and cylinder heads.

1. Suction Valve

2. Suction Valve Positioning Spring

3. Valve Plate Dowel Pin

Figure 4-12. Suction Valve & Positioning Springs

b. Compression Rings

1. Depending on date of manufacture, the

compressor may be equipped with double or single ring

pistons. This variation may also exist with replacement

piston assemblies. If double ring pistons and ring sets are

to be installed, both compression rings must be installed.

Also, double ring and single ring pistons may be installed

in the compressor.

2. The compression ring is chamfered on the inside

circumference. This ring is installed with the chamfer

towards the top. If using a double ring piston, stagger the

ring end gaps so they are not aligned.

The gap between the ends of the piston rings can

be checked with a feeler gauge by inserting the ring into

the piston bore about one inch below the top of the bore.

Square the ring in the bore by pushing it slightly with a

piston. The maximum and minimum allowable ring gaps

are 0.33 and 0.127 mm (0.013 and 0.005 inch)

Compression ring

Figure 4-13. Piston Rings

c. Installing the Components

1. Install the crankshaft through the pump end of

the compressor. Do not damage main bearings. Push

pistons from the inside of the crankcase through the

cylinders being careful not to break the rings. Place

chamfered side of connecting rod against radius of

crankpins. Install matching connecting rod caps through

bottom cover plate.

2. The oil screen (located in the bottom of the

crankcase), is connected to the inlet of the oil pump.

Whenever the compressor crankcase is opened, inspect

the screen for holes or an accumulation of dirt. The

screen can be cleaned with a suitable solvent.

There are two types of oil pumps; vane and gear. See

Figure 4-3 to identify which oil pump is used, then follow

the correct procedure below.

Vane Oil Pump (See Figure 4-6):

a. Install the bearing head assembly with a new gasket

on the compressor crankshaft. Carefully push oil pump

on by hand ensuring that the bearing head mounts flush

to the crankcase body. The top of the bearing head is

marked on the mounting flange.
b. Align the gasket and install the eight capscrews in the

mounting flange.
c. Install the drive segment with the two capscrews and

lock washer.
d. Insert the oil feed guide with the large diameter in.

Insert the guide retaining spring so that it fits over the

smaller diameter of the feed guide. The pump cover can

now be installed.
e. Place the pump cover, with a new gasket, over the

guide retaining spring and compress the spring to enable

installation of the cover capscrews.

Gear Oil Pump (See Figure 4-7):

a. Install the pump end thrust washer on the two dowel

pins located on the bearing head.

CAUTION

Ensure that the thrust washer does not fall off

the dowel pins while installing the oil pump.

b. Install the bearing head assembly with a new gasket

on the compressor crankshaft. Carefully push the oil

pump on by hand ensuring that the thrust washer remains

on the dowel pins, the tang on the end of the drive

segment engages the slot in the crankshaft, and the oil

inlet port on the pump is aligned with the oil pickup tube

in the crankcase. The pump should mount flush with the

crankcase.
c. Align the gasket and install the eight capscrews in the

mounting flange.

3. Install rotor with key. Screw on equalizer tube

and lock screw assembly with lock washer and bend over

tabs of lock washer. Assemble suction strainer to motor

and cover and bolt cover to crankcase. Assemble valve

plates and gaskets. Assemble cylinder heads and gaskets.

Feel if the shaft will turn by hand.

4. Install oil suction screen and bottom plate.

4.8 CHECKING THE COMPRESSOR

OIL LEVEL

a. To Check the Oil Level in the Compressor:

1. Operate the unit in six cylinder cooling for at

least 20 minutes.

2. Check the front oil sight glass on the compressor

to ensure that no foaming of the oil is present after 20

minutes of operation. If the oil is foaming excessively

after 20 minutes of operation, check the refrigerant

system for flood-back of liquid refrigerant. Correct this

situation before performing step a.3.

Downloaded from

ManualsNet.com

search engine

Содержание TRANSICOLD 69NT20-274























































































































































































Результаты поиска

Содержание TRANSICOLD 69NT20-274

Отзывы:

Похожие инструкции для TRANSICOLD 69NT20-274

Бренды по названию

Популярные бренды

Carrier TRANSICOLD 69NT20-274, Операция и обслуживание

Результаты поиска

Содержание TRANSICOLD 69NT20-274

Отзывы:

Похожие инструкции для TRANSICOLD 69NT20-274

Бренды по названию

Популярные бренды