Carrier INFINITY 24ANA Скачать руководство пользователя страница 11

11

TIME DELAYS

The unit time delays include:

S

Five minute time delay to start cooling or heating
operation when there is a call from the thermostat or user
interface. To bypass this feature, momentarily short and

release Forced Defrost pins.

S

Five minute compressor re--cycle delay on return from a
brown--out condition.

S

Two minute time delay to return to standby operation
from last valid communication (with Infinity only).

S

One minute time delay of outdoor fan at termination of

cooling mode when outdoor ambient is greater than or

equal to 100

_

F.

S

On 24ANA7 models there is a 1 minute time delay
between staging from low to high and from high to low
capacity. On 24ANA1 models there is no delay; the

compressor will change from low to high and from high
to low capacity on the fly to meet the demand.

LOW AMBIENT COOLING

If this unit will be required to operate below 55

_

F outdoor

temperature, provisions must be made for low ambient operation.

Infinity Controlled low ambient cooling:

This unit is capable of low ambient cooling down to 0

_

F without

a kit ONLY when using Infinity control. A low ambient kit is not

required, and the outdoor fan motor does not need to be replaced

for Infinity controlled low ambient operation. The Infinity
Control provides an automatic evaporator coil freeze protection

algorithm that eliminates the need for an evaporator freeze
thermostat. Low ambient cooling must be enabled in the User

Interface set up. Fan may not begin to cycle until about 40

_

F

OAT. Fan will cycle based on coil and outdoor air temperature.
Infinity controlled low ambient mode operates as follows:

S

Fan is OFF when outdoor coil temp is < (outdoor air
tempe 3

_

F) or outdoor fan has been ON for 30

minutes. (Fan is turned off to allow refrigerant system to
stabilize.)

S

Fan is ON when outdoor coil temp > (outdoor air
tempe 25

_

F) or outdoor coil temp > 80

_

F or if

outdoor fan has been OFF for 30 minutes. (Fan is turned
on to allow refrigerant system to stabilize.)

S

Low pressure switch is ignored for first 3 minutes during
low ambient start up. After 3 minutes, if LPS trips, then
outdoor fan motor is turned off for 10 minutes, with the

compressor running. If LPS closes within 10 minutes
then cooling continues with the outdoor fan cycling per

the coil temperature routine listed above for the remainder
of the cooling cycle. If the LPS does not close within 10
minutes, then the normal LPS trip response (shut down

cooling operation and generate LPS trip error) will occur.

UTILITY RELAY  

*

UTILITY SIGNAL

OPEN RELAY

*

 SUPPLIED BY UTILITY PROVIDER

LLS

Liquid Line Solenoid

A05247

Fig. 10

---

2--Stage Control Board

24AN

A

Содержание INFINITY 24ANA



















Отзывы: