Carrier AQUAZONE 50HQL072-120 Скачать руководство пользователя

Страница: 35 / 44

OPERATION

Power Up Mode —

The unit will not operate until all

the inputs, terminals and safety controls are checked for

normal operation.
NOTE: The compressor will have a 5-minute anti-short

cycle upon power up.

Units with Aquazone™ Complete C Control

STANDBY — Y and W terminals are not active in Standby

mode, however the O and G terminals may be active, de-

pending on the application. The compressor will be off.
COOLING — Y and O terminals are active in Cooling

mode. After power up, the first call to the compressor will

initiate a 5 to 80 second random start delay and a 5-minute

anti-short cycle protection time delay. After both delays are

complete, the compressor is energized.
NOTE: On all subsequent compressor calls the random start

delay is omitted.
HEATING STAGE 1 — Terminal Y is active in heating

stage 1. After power up, the first call to the compressor will

initiate a 5 to 80 second random start delay and a 5-minute

anti-short cycle protection time delay. After both delays are

complete, the compressor is energized.
NOTE: On all subsequent compressor calls the random start

delay is omitted.
HEATING STAGE 2 — To enter Stage 2 mode, terminal W

is active (Y is already active). Also, the G terminal must be

active or the W terminal is disregarded. The compressor re-

lay will remain on and EH1 is immediately turned on. EH2

will turn on after 10 minutes of continual stage 2 demand.
NOTE: EH2 will not turn on (or if on, will turn off) if FP1

temperature is greater than 45 F and FP2 is greater than

110 F.
EMERGENCY HEAT — In emergency heat mode, termi-

nal W is active while terminal Y is not. Terminal G must be

active or the W terminal is disregarded. EH1 is immediately

turned on. EH2 will turn on after 5 minutes of continual

emergency heat demand.

Units with Aquazone Deluxe D Control

STANDBY/FAN ONLY — The compressor will be off.

The Fan Enable, Fan Speed, and reversing valve (RV) relays

will be on if inputs are present. If there is a Fan 1 demand,

the Fan Enable will immediately turn on. If there is a Fan 2

demand, the Fan Enable and Fan Speed will immediately

turn on.
NOTE: DIP switch 5 on S1 does not have an effect upon

Fan 1 and Fan 2 outputs.
HEATING STAGE 1 — In Heating Stage 1 mode, the Fan

Enable and Compressor relays are turned on immediately.

Once the demand is removed, the relays are turned off and

the control reverts to Standby mode. If there is a master/

slave or dual compressor application, all compressor relays

and related functions will operate per their associated DIP

switch 2 setting on S1.
HEATING STAGE 2 — In Heating Stage 2 mode, the Fan

Enable and Compressor relays are remain on. The Fan

Speed relay is turned on immediately and turned off imme-

diately once the demand is removed. The control reverts to

Heating Stage 1 mode. If there is a master/slave or dual

compressor application, all compressor relays and related

functions will operate per their associated DIP switch 2

setting on S1.
HEATING STAGE 3 — In Heating Stage 3 mode, the Fan

Enable, Fan Speed and Compressor relays remain on. The

EH1 output is turned on immediately. With continuing Heat

Stage 3 demand, EH2 will turn on after 10 minutes. EH1

and EH2 are turned off immediately when the Heating Stage

3 demand is removed. The control reverts to Heating Stage

2 mode.

Output EH2 will be off if FP1 is greater than 45 F AND

FP2 (when shorted) is greater than 110 F during Heating

Stage 3 mode. This condition will have a 30-second

recognition time. Also, during Heating Stage 3 mode, EH1,

EH2, Fan Enable, and Fan Speed will be ON if G input is

not active.
EMERGENCY HEAT — In Emergency Heat mode, the

Fan Enable and Fan Speed relays are turned on. The EH1

output is turned on immediately. With continuing Emergen-

cy Heat demand, EH2 will turn on after 5 minutes. Fan En-

able and Fan Speed relays are turned off after a 60-second

delay. The control reverts to Standby mode.

Output EH1, EH2, Fan Enable, and Fan Speed will be

ON if the G input is not active during Emergency Heat

mode.
COOLING STAGE 1 — In Cooling Stage 1 mode, the Fan

Enable, compressor and RV relays are turned on immediate-

ly. If configured as stage 2 (DIP switch set to OFF) then the

compressor and fan will not turn on until there is a stage 2

demand. The Fan Enable and compressor relays are turned

off immediately when the Cooling Stage 1 demand is re-

moved. The control reverts to Standby mode. The RV relay

remains on until there is a heating demand. If there is a mas-

ter/slave or dual compressor application, all compressor re-

lays and related functions will track with their associated

DIP switch 2 on S1.
COOLING STAGE 2 — In Cooling Stage 2 mode, the Fan

Enable, compressor and RV relays remain on. The Fan

Speed relay is turned on immediately and turned off once

the Cooling Stage 2 demand is removed. The control reverts

to Cooling Stage 1 mode. If there is a master/slave or dual

compressor application, all compressor relays and related

functions will track with their associated DIP switch 2 on

S1.
NIGHT LOW LIMIT (NLL) STAGED HEATING — In

NLL staged Heating mode, the override (OVR) input be-

comes active and is recognized as a call for heating and the

control will immediately go into a Heating Stage 1 mode.

With an additional 30 minutes of NLL demand, the control

will go into Heating Stage 2 mode. With another additional

30 minutes of NLL demand, the control will go into Heating

Stage 3 mode.

Units with HWR Option

FAN ONLY — A (G) call from the thermostat to the (G)

terminal of the Deluxe D control board will bring the unit

on in fan only mode.
COOLING STAGE 1 — A simultaneous call from (G),

(Y1), and (O) to the (G), (Y1), (O/W2) terminals of the

Deluxe D control board will bring the unit on in Cooling

Stage 1.
COOLING STAGE 2 — A simultaneous call from (G),

(Y1), (Y2), and (O) to the (G), (Y1), (Y2), and (O/W2) ter-

minals of the Deluxe D control board will bring the unit on

in Cooling Stage 2. When the call is satisfied at the thermo-

stat the unit will continue to run in Cooling Stage 1 until the

Cooling Stage 1 call is removed or satisfied, shutting down

the unit.
NOTE: Not all units have two-stage cooling functionality.
HEATING STAGE 1 — A simultaneous call from (G) and

(Y1) to the (G) and (Y1) terminals of the Deluxe D control

board will bring the unit on in Heating Stage 1.
HEATING STAGE 2 — A simultaneous call from (G),

(Y1), and (Y2) to the (G), (Y1), and (Y2) terminals of the

Deluxe D control board will bring the unit on in Heating

Содержание AQUAZONE 50HQL072-120













































Результаты поиска

Содержание AQUAZONE 50HQL072-120

Отзывы:

Похожие инструкции для AQUAZONE 50HQL072-120

Бренды по названию

Популярные бренды

Carrier AQUAZONE 50HQL072-120, Инструкция по установке, запуску и обслуживанию

Результаты поиска

Содержание AQUAZONE 50HQL072-120

Отзывы:

Похожие инструкции для AQUAZONE 50HQL072-120

Бренды по названию

Популярные бренды