background image

 

2050 Operations Manual 

Rev L    2/2/2018 

Page 7 of 22 

 

 

 

 

 

 

EQUIPMENT INTERNATIONAL LIMITED WARRANTY 

 

Please review this section before requesting warranty service.  At CARON, one of our primary goals is 
to provide customers with high levels of personal service and top quality products, delivered on time, 
backed by technical service and supported for the life of the product. 

 

Before contacting your distributor for warranty service, please be aware that there are repairs 
that are not covered under warranty.   
 
WARRANTY DEFINED 
Caron Products & Services, Inc. (herein after CARON) hereby warrants that equipment manufactured 
by  CARON  is  free  from  defects  in  materials  and  workmanship  when  the  equipment  is  used  under 
normal operating conditions in accordance with the instructions provided by CARON. 
 
COVERED: 

  Parts for a period of two (2) years from date of shipment. 

  Any  part  found  defective  will  be  either  repaired  or  replaced  at  CARON's  or  their  authorized 

representative’s discretion. Parts that are replaced will become the property of CARON. 

  If  CARON  or  their  authorized  representatives  determine  that  the  customer's  unit  requires  further 

service,  CARON  or  the  representative  may,  at  its  sole  discretion,  provide  a  service  technician  to 
correct the problem, or require the return of the equipment to the an authorized service depot.   

  CARON  or  their  authorized  representative  will  have  the  right  to  inspect  the  equipment  and 

determine  the  repairs  or  replacement  parts  necessary.    The  customer  will  be  notified,  within  a 
reasonable time after inspection, of any costs incurred that are not covered by this warranty prior 
to initiation of any such repairs. 

 
NOT COVERED: 

  Calibration of control parameters. 

  Improper installation; including electrical service, gas and water supply tubing, gas supplies, room 

ventilation,  unit  leveling,  facility  structural  inadequacies  or  ambient  conditions  that  are  out  of 
specification. 

  Cost of express shipment of equipment or parts.  

  Any customer modifications of this equipment, or any repairs undertaken without the prior written 

consent of CARON, will render this limited warranty void. 

  CARON  and  their  representative  are  not  responsible  for  consequential,  incidental  or  special 

damages; whether shipping damage or damages that may occur during transfer to the customer’s 
point of use. When the equipment is signed for at the customer’s site, ownership is transferred to 
the customer. Any damage claims against the shipping company become the responsibility of the 
customer.  

  Repairs  necessary  because  of  the  equipment  being  used  under  other  than  normal  operating 

conditions or for other than its intended use. 

  Repair due to the customer's failure to follow normal maintenance instructions. 

  Parts considered consumable; including: light bulbs, filters, gases, etc. 

  Damage from use of improper water quality. 

  Damage from chemicals or cleaning agents detrimental to equipment materials. 

  Force Majeure or Acts of God. 

Содержание 2050























Отзывы: