manualshive.com logo in svg

Carmanah SpeedCheck-18, Руководство пользователя, Страница: 45 / 46

Поделиться
Скачать
Carmanah SpeedCheck-18 Скачать руководство пользователя страница 45

 

  

 

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | 

[email protected]

 | 

carmanah.com

     

45

 

SPEEDCHECK-15/18 USER MANUAL 

9.0 SERVICE & REPAIR 

 

9.7  Programmable Board Display Cable Connections (with Slow Down) 

If your display includes the Slow Down Display option, note the following cable connections (

connect the display 

cables before connecting the power cable

): 

1.  The Right-Side display connection cables are bundled together. Note the orientation of the wires. The 

index pins on the cable socket fit into notches in the board plug. 

2.  The Left-Side display connection is a single cable with a 7-pin connector. Note the orientation of the 

wires. The index pins on the cable socket fit into notches in the board plug. 

3.  Jumper connection between left and right display. The cables exit the connector towards the opposite 

display board. The board plug pins may be on either the front or the back, but the cable installs the same 

way. 

4.  Cable connections to the SpeedCheck Controller consist of four cables connected as shown in the photo 

below. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Left Display Board Connector 

Right Display Board Connectors 

Slow Down Interconnect 

SpeedCheck Controller Connectors 

Содержание SpeedCheck-18















































Отзывы:

Нет отзывов