manualshive.com logo in svg

Carmanah SpeedCheck-18, Руководство пользователя, Страница: 22 / 46

Поделиться
Скачать
Carmanah SpeedCheck-18 Скачать руководство пользователя страница 22

 

  

 

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | 

[email protected]

 | 

carmanah.com

     

22

 

SPEEDCHECK-15/18 USER MANUAL 

4.0 INSTALLATION 

 

4.6  Cabinet Installation 

Before mounting the cabinet to the pole, all wiring internal to the pole (power, LED, optional 
StreetHub™serial and ground cables) should be fished.

 

1.  Loosen four nuts on back of cabinet and spread brackets outward. Tighten nuts to 20 ft-lb.    

 

 

 

 

 

 

 

 

 

 

On the back of the cabinet, there are 2 drill points that may be used for routing of liquid-tight 
conduit external to the mounting pole. Prior to drilling the cabinet, ensure there are no 
components which may be damaged on the inside of the cabinet

. 

2.  Drill a 1-

3/4” diameter hole in pole for cabinet pipe nipple at desired position.  

 

3.  Route cables from pole into cabinet and temporarily affix cabinet against the pole. For U-bolt mounting, 

install U-bolts, washers and nuts then torque to 30 ft-lb. For banding, install banding through openings in 
brackets. 

 

 

 

 

 

 

 

 

 

 

4.  If desired, before tightening banding, brackets and banding can be adjusted inboard again. Tighten 

banding (up to ¾” wide) as per banding manufacturer’s instructions. 

Содержание SpeedCheck-18















































Отзывы:

Нет отзывов