Carmanah SpeedCheck-18 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 46

Carmanah SpeedCheck-18 Скачать руководство пользователя страница 20

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

20

SPEEDCHECK-15/18 USER MANUAL

4.0 INSTALLATION

4.4 Quick Change Pole Mount

1. Remove sign face from main enclosure to allow for easier access.

2. Fasten the top bracket to the sign enclosure (Note: Legacy version with angled top shown pictured below.

New version has a flat top.)

3. Fasten bottom bracket to the sign enclosure.

4. Loosely secure the top bracket hanger to the pole using hose clamp.

5. Hang sign enclosure without sign face on top of the top bracket hanger.

6. Loosely secure the bottom bracket hanger to the pole using hose clamp.

7. Make fine adjustments for alignment and commissioning (see

).

8. Once the alignment has been validated, secure the brackets to the pole in a more permanent manner

using stainless-steel banding (not provided) or U-bolts (an orderable option).

9. Complete installation wiring.

10. Attach sign face.

11. Secure cabinet in place with padlock.

Lower Housing Mounting Bracket

Upper Housing Mounting Bracket

(Note legacy angled top version

shown)

Top Bracket Hanger

Installed Top Bracket

Installed Bottom Bracket

«
...
18
19
20
21
22
...
»

Содержание SpeedCheck-18















































Отзывы:

Нет отзывов