Carmanah SpeedCheck-18 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 46

Carmanah SpeedCheck-18 Скачать руководство пользователя страница 30

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

30

SPEEDCHECK-15/18 USER MANUAL

5.0 DISPLAY ALIGNMENT

Roadside Placement

Typically, the SpeedCheck display sign is mounted between five and twelve feet from the roadside. As this
diagram shows, the display sign should also be mounted at least five feet above the road grade. To meet Manual
on Uniform Traffic Control Devices (MUTCD) standards, the bottom of the sign must be seven feet above the
ground.

Road Grades and Curvatures

An installation in the uphill or downhill direction of a steep hill might require the display sign to be mounted with
the top tilted towards oncoming vehicles to accurately aim the radar at approaching traffic. In this situation, use
spacers behind the top or bottom display mounting bracket to tilt the display sign away from the pole, so that the
housing is more perpendicular to the grade. Tilt brackets are available for this purpose.

«
...
28
29
30
31
32
...
»

Содержание SpeedCheck-18















































Отзывы:

Нет отзывов