background image

CARLO GAVAZZI

17

Function      

Settings

[Factory settings] shown in brackets

Press 

▲ 

or 

▼ 

to change

Press 

✱ ▲ 

or 

✱ ▼ 

to change

E.oP

Event output

[nonE]

Function can be applied to each 
segment independently to trigger 
an output for the full duration of 
that segment. Setting blocked 
unless either or both outputs SP2A
or SP3A have been configured as 
an 

Event Output

in Level 2 or 

Level A respectively.

2d

SP2A de-energised to mark event

2E

SP2A energised to mark event

3d

SP3A de-energised to mark event

3E

SP3A energised to mark event

2d.3d

SP2A and SP3A de-energised to 
mark event 

2E.3d

SP2A energised SP3A de-energised
to mark event

2E.3E

SP2A and SP3A energised to mark 
event

2d.3E

SP2A de-energised SP3A energised
to mark event

To Return to:

LEVL P

Press and hold 

To Read % Programmer memory used:

USEd

Press 

✱ 

and 

together in LEVL P / ProG 1

1–100%

Memory Allocation Table

Segment type 

Memory required

Ramp

4 Bytes

Ramp with Holdback

5 Bytes

Soak

2 Bytes

Step

3 Bytes

Loops (1–3)

1 Byte

Loops (4+)

2 Bytes

Call

1 Byte

Event Output

1 Byte

Program Header

1 Byte

Maximum capacity:

351 Bytes

31 Programs

126 Segments

Examples:

1. 1 program of 58 Ramps and 58 Soaks

349 Bytes

2. 4 programs of 14 Ramps and 14 Soaks

340 Bytes

3. 31 programs of 2 Ramps and 1 Soak

341 Bytes

4. 2 programs of 10 Ramps, 10 Soaks, 2 Steps and 1 loop

136 Bytes

Memory Full Indication

Should the programmer memory capacity be reached during program configuration, the
display will show ‘FULL’

Содержание T2000P Series

























Отзывы: