Carl Goldberg Products skylane 62 arf Скачать руководство пользователя страница 22

Страница: 22 / 24

RECEIVER AND BATTERY INSTALLATION

Insert the Y-harness into the the aileron

plug in the receiver and then wrap both the

receiver and the battery in the 1/2" foam.

The switch can be mounted in the fuselage

side opposite the exhaust.

You can remove the tank and place the bat-

tery under the tank or it can be placed just in

front of the servo tray depending on where

you need it for balance. If the battery is

under the tank the receiver can go just in

front of the servo tray. If the battery is in front

of the servo tray you can mount the receiver

behind the servo tray under the pushrods.

Move the battery and receiver to achieve the

proper balance.

WING AND STRUT MOUNTING

Collect the following items:

(2) Wing Struts
(4) 3mm x 12mm socket head screws

(2) 4mm x 25mm socket head screws

(2) 4mm flat washers

Fit the wing into the saddle with the tongue

on the bottom of the bottom of the wing fit-

ting into the notch at the leading edge.

Содержание skylane 62 arf

























Результаты поиска

Содержание skylane 62 arf

Отзывы:

Похожие инструкции для skylane 62 arf

Бренды по названию

Популярные бренды

Carl Goldberg Products skylane 62 arf, Инструкция по эксплуатации

Результаты поиска

Содержание skylane 62 arf

Отзывы:

Похожие инструкции для skylane 62 arf

Бренды по названию

Популярные бренды