Carl Goldberg Products skylane 62 arf Скачать руководство пользователя | Manualshive

Страница: 14 / 24

background image

14

6.

Attach the two pieces of 5mm tubing to

the two tank outlets. Use different colors

so you can tell which is the vent and

which is the fuel pickup after the tank is

installed. Make a note of which color you

attach to which tube. The short brass

with the clunk is the fuel pickup and must

go to the carburetor. The long brass tube

is the vent and should go to the pressure

outlet on the muffler.

Set tank aside till ready to install.

5.

Install the assembly into the tank so the

vent tube is turned up to the top of the

tank and is positioned on the right side of

the tank. Tighten the screw to expand

the rubber cap. Don’t over tighten or you

could split the tank.

3.

Position the two metal straps over the gear

legs where they turn up into the fuselage on

both sides.

Drill a 1/16” hole through each gear strap

and install the 2mm screw and flat washer.

1.

Gather the following items:

(4) 2mm x 12mm screws

(4) 2mm washer

(2) Metal gear straps

(2) Main gear wire

(1) Nose Gear Wire

(6) 4mm wheel collar

(1) Nylon steering arm

(1) set screw for steering arm

(3) 2-1/2” wheels

LANDING GEAR INSTALLATION

2.

Insert the main gear wires in the pre-cut

holes and slots in the bottom of the fuse-

lage.

«
...
12
13
14
15
16
...
»

Содержание skylane 62 arf

























Отзывы:

Нет отзывов

Похожие инструкции для skylane 62 arf

Бренд: Team C Страницы: 33

Бренд: FUTABA Страницы: 2

Бренд: GRAUPNER Страницы: 42

Бренд: Viessmann Страницы: 3

Steaman Aerobatic Biplane

Бренд: REVELL Страницы: 12

Бренд: Makeblock Страницы: 3

Бренд: Playlearn Страницы: 4

Бренд: Bengtson Company Страницы: 7

Бренд: Lionel Страницы: 8

EI-2309 Language Tutor

Бренд: Educational Insights Страницы: 8

Бренд: Flex innovations Страницы: 31

Train Orders Building

Бренд: Lionel Страницы: 8

Techno Gears Marble Mania Renegade

Бренд: The Learning Journey Страницы: 178

Бренд: marklin Страницы: 12

Musical Cuddle Bug

Бренд: VTech Baby Страницы: 11

Бренд: My Little Pony Страницы: 2

Бренд: Nine Eagles Страницы: 14

Бренд: spacewalker Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды