![Carel SD Скачать руководство пользователя страница 40](http://html.mh-extra.com/html/carel/sd/sd_user-manual_2557582040.webp)
E31 - Malfunzionamento
sonda/regolatore esterno
Quando il segnale di sonda/regolatore esterno assume
valori fuori range
Vedi E14
Funzionamento umidificatore senza regolazione
esterna
N.B. si raccomanda di eseguire le operazioni seguenti con
l’umidificatore spento
CDH
scollegare la sonda - posizionare dip-switch 1 ON
gli altri OFF
CDP
scollegare il regolatore modulante - posizionare
dip-switch 2, 6 ON gli altri OFF – inserire un ponticello
tra i morsetti 56-57 e un altro tra i morsetti 58-59A
CDC
scollegare l’umidostato – verificare il posizionamento
dip-switch 4, 6 ON gli altri OFF – inserire un ponticello
tra i morsetti 56-57 e un altro tra i morsetti 58-59A
E32 - Autotest fallito
Il sistema non acquisisce dati dalla memoria interna
Causa
1 Guasto
hardware
2
Controllo non programmato
Verifiche e soluzioni
1-2 Riprogrammare il controllo per via seriale tramite il
programma di configurazione Carel
L’umidificatore non si accende
Non arriva tensione al quadro elettrico
Causa
Alimentazione generale non attiva
Verifiche e soluzioni
Verificare la protezione a monte dell’umidificatore
Il controllo non è alimentato
Causa
1
Connettori del controllo non bene inseriti
2
Contatto ON-OFF remoto (morsetti 20-21) aperto
3
Uscita trasformatore di alimentazione guasta
4
Interruttore a pannello aperto
5
Intervento delle protezioni a fusibile
Verifiche e soluzioni
1
Verificare che i connettori siano ben inseriti
2
Verifica stato ON-OFF (morsetti 20-21 ponticellati)
3
Verificare che al secondario del trasformatore ci siano 24 Vac
4
Chiudere l’interruttore a pannello
5
Verificare lo stato dei fusibili al primario/secondario
F1, F2, F3
36
E31 - Malfunctioning
probe/external regulator
When the probe/regulator signal takes out-of-range values
See E14
Functioning of the humidifier without external
regulation
N.B. It is advisable to do the following operations with the
humidifier OFF
CDH
disconnect the probe - position dip-switch 1 ON the
others OFF
CDP
disconnect the modulating regulator-position dip-switch
2, 6 ON the others OFF – insert a jumper between
the terminals 56-57 and another one between the
terminals 58-59A
CDC
disconnect the humidostat – check the positioning
dip-switch 4, 6 ON and the others OFF – insert a
jumper between 56-57 and another between the
terminals 58-59A
E32 - Autotest failure
The system does not acquire data from the internal
memory
Cause
1 Faulty
hardware
2
Not programmed control
Checkings and solutions
1-2 Program again the controller via serial line through
the Carel configuration program
The humidifier does not start
No current at the electrical panel
Cause
General power supply not energized
Checkings and solutions
Check the protection upstream to the humidifier
No power supply to the controller
Cause
1
Control connector not properly inserted
2
Remote ON-OFF contact (terminals 20-21) open
3
Power supply transformer output fault
4
Panel switch open
5
Fuse protections trip
Checkings and solutions
1
Check that the connectors are correctly inserted
2
Check ON-OFF conditions (terminals 20-21 bridged)
3
Check that at the secondary of the transformer there
are 24Vac
4
Close the panel switch
5
Check the fuse conditions at the primary/secondary
F1, F2, F3
LED Relè Segnale
Ripristino
ON
ON
Allarme Automatico
LED Relè Segnale
Ripristino
ON
ON
Allarme Automatico
LED Relay Signal
Reset
ON
ON
Alarm
Automatic
LED Relay Signal
Reset
ON
ON
Alarm Automatic
Содержание SD
