background image

3

EN

“UEX-PLUS” +030220621 - rel. 1.4 - 04.08.2009

WARNINGS

The CAREL S.p.A. humidifi ers are advanced products, whose operation is 
specifi ed in the technical documentation supplied with the product or can be 
downloaded, even prior to purchase, from the website www

 

.carel.

 

com. Each 

CAREL S.p.A. product, in relation to its advanced level of technology, requires 
setup/confi guration/programming/commissioning to be able to operate in 
the best possible way for the specifi c application. The failure to complete such 
operations, which are required/indicated in the user manual, may cause the 
fi nal product to malfunction; CAREL S.p.A. accepts no liability in such cases.
The customer (manufacturer, developer or installer of the fi nal equipment) 
accepts all liability and risk relating to the confi guration of the product in 
order to reach the expected results in relation to the specifi c fi nal installation 
and/or equipment. CAREL S.p.A.  may, based on specifi c agreements, acts as a 
consultant for the installation/commissioning/use of the unit, however in no 
case does it accept liability for the correct operation of the humidifi er and the 
fi nal installation if the warnings or suggestions provided in this manual or in 
other product technical documents are not heeded. In addition to observing 
the above warnings and suggestions, the following warnings must be heeded 
for the correct use of the product: 

DANGER OF ELECTRIC SHOCK  

• 

 

The humidifi er contains live electrical components. Disconnect the mains 
power supply before accessing inside parts or during maintenance and 
installation.

DANGER OF WATER LEAKS

• 

The humidifi er automatically and constantly fi lls/drains certain quantities of 
water. Malfunctions in the connections or in the humidifi er may cause leaks.

DANGER OF BURNS

• 

The humidifi er contains high temperature components and delivers steam 
at 100°C/ 212°F.

Important

Important

:

The installation of the product must include an earth connection, using the 

• 

special yellow-green terminal available in the humidifi er.
The environmental and power supply conditions must conform to the 

• 

values specifi ed on the product rating labels. 
The product is designed exclusively to humidify rooms either directly or 

• 

through distribution systems (ducts). 
Only qualifi ed personnel who are aware of the necessary precautions and 

• 

able to perform the required operations correctly may install, operate or 
carry out technical service on the product. 
Only water with the characteristics indicated in this manual must be used 

• 

for steam production. 
All operations on the product must be carried out according to the 

• 

instructions provided in this manual and on the labels applied to the 
product. Any uses or modifi cations that are not authorised by the 
manufacturer are considered improper. CAREL S.p.A. declines all liability for 
any such unauthorised use. 
Do not attempt to open the humidifi er in ways other than those specifi ed 

• 

in the manual.
Observe the standards in force in the place where the humidifi er is 

• 

installed.
Keep the humidifi er out of the reach of children and animals. 

• 

Do not install and use the product near objects that may be damaged when 

• 

in contact with water (or condensate). CAREL S.p.A. declines all liability for 
direct or indirect damage following water leaks from the humidifi er. 
Do not use corrosive chemicals, solvents or aggressive detergents to clean 

• 

the inside and outside parts of the humidifi er, unless specifi cally indicated 
in the user manual.
Do not drop, hit or shake the humidifi er, as the inside parts and the linings 

• 

may be irreparably damaged.

CAREL S.p.A. adopts a policy of continual development. Consequently, CAREL 
reserves the right to make changes and improvements to any product 
described in this document without prior warning. The technical specifi cations 
shown in the manual may be changed without prior warning.
The liability of CAREL S.p.A. in relation to its products is specifi ed in the 
CAREL S.p.A. general contract conditions, available on the website www

 

.

carel.

 

com and/or by specifi c agreements with customers; specifi cally, to the 

extent where allowed by applicable legislation, in no case will CAREL S.p.A., 
its employees or subsidiaries be liable for any lost earnings or sales, losses 
of data and information, costs of replacement goods or services, damage to 
things or people, downtime or any direct, indirect, incidental, actual, punitive, 

exemplary, special or consequential damage of any kind whatsoever, whether 
contractual, extra-contractual or due to negligence, or any other liabilities 
deriving from the installation, use or impossibility to use the product, even if 
CAREL S.p.A. or its subsidiaries are warned of the possibility of such damage.

DISPOSAL

The humidifi er is made up of metal parts and plastic parts. In reference to 
European Union directive 2002/96/EC issued on 27 January 2003 and the 
related national legislation, please note that:

WEEE cannot be disposed of as municipal waste and such waste must be 

1. 

collected and disposed of separately;
the public or private waste collection systems defi ned by local legislation 

2. 

must be used. In addition, the equipment can be returned to the distributor 
at the end of its working life when buying new equipment;
the equipment may contain hazardous substances: the improper use or 

3. 

incorrect disposal of such may have negative eff ects on human health and 
on the environment;
the symbol (crossed-out wheeled bin) shown on the product or on the 

4. 

packaging and on the instruction sheet indicates that the equipment has 
been introduced onto the market after 13 August 2005 and that it must 
be disposed of separately;
in the event of illegal disposal of electrical and electronic waste, the 

5. 

penalties are specifi ed by local waste disposal legislation.

Warranty on the materials: 

2 years (from the date of production, excluding 

consumables).

Approval:  

the quality and safety of CAREL S.P.A. products are guaranteed by 

the ISO 9001 certifi ed design and production system, as well as by the   

 

mark.

Содержание humiSteam x-plus





























































Отзывы: