Carefree TRAVEL'R ADJUSTABLE PITCH Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 48

Carefree TRAVEL'R ADJUSTABLE PITCH Скачать руководство пользователя страница 8

Carefree of Colorado

Service Manual

T

RAVEL

'

R

052540-301r10

5

M

OTOR

R

EPLACEMENT

STOP!

Before continuing, it is necessary to

determine which motor configuration is installed on
the awning. S

ERIES

I uses a bent sheet metal

mounting frame. S

ERIES

II uses a cast metal

mounting frame. The mounting and attachment of
the two configurations are different. To distinguish
between the two, look at the motor head. The bent
sheet metal frame (Series I) has two protruding
bumps in the front cover. There are also two
exposed rivets on each side of the arm channel.
The cover for the cast metal (Series II) is smooth
and there are no rivets.

NOTE: Motor assemblies and covers are not interchangeable between the two configurations.

R

EPLACING THE

M

OTOR

–

S

ERIES

I

Spacers
(qty: 11)

3/8-16 x 6 Bolt

Front Cover

Rear Cover

3/8-16

Lock Nut

Travelr015

Motor

End Cap

#10 x 5/8 Screw

DETAIL

D

DETAIL

A

Motor - Red Wire
Cable - Red Wire

Motor - Black Wire
Cable - Black Wire

DETAIL

C

Motor (ref)

Motor Attach
Bolts & Nuts

Rear Cover
(ref)

Front Cover

(ref)

DETAIL

B

Motor Assembly

W/ Bent Metal

Frame

Figure 2. Motor Replacement – Series I.

1.

(refer to Detail A) For Awnings Fully or Partially Extended:

1.1 On the right hand arm remove the front cover by removing the six (6) smaller screws from the back

of the motor head. Save cover and screws.

1.2 Disconnect the motor and cable wires from inside the rear cover. Note the location of each wire.

1.3 Remove the rear cover by removing the one (1) large screw from the back of the motor head.

Save cover and screw.

1.4 Go to step 3.

Travelr016

Configuration A

Bent Sheetmetal

Motor Mount Frame

Configuration B

Cast Metal

Motor Mount Frame

External
Rivets

Protruding

Bumps in

Front Cover

Figure 1. Distinguishing the Motor Mount.

«
...
6
7
8
9
10
...
»

Содержание TRAVEL'R ADJUSTABLE PITCH

















































Отзывы:

Нет отзывов