Carefree TRAVEL'R ADJUSTABLE PITCH Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 48

Carefree TRAVEL'R ADJUSTABLE PITCH Скачать руководство пользователя страница 16

Carefree of Colorado

Service Manual

T

RAVEL

'

R

052540-301r10

13

D04 D

IRECT

R

ESPONSE

A

WNING

D

OES

N

OT

A

UTO

-R

ETRACT

D

URING

W

INDY

C

ONDITIONS

The auto - retract system is only active when the power switch is in the ON position.
A

Confirm awning operates normally using the standard
extend/retract switch with power on.

YES

Module is defective - replace

NO

Go to Test D05

D05 D

IRECT

R

ESPONSE

S

TANDARD

O

PERATION

A

Check Installation Integrity
Use the wiring diagram and confirm that the components and
wiring are properly installed and connected

YES

Go to test B

NO

Correct as required

B

Confirm Power Supply
Is vehicle battery or power source providing 10V to 14V to the
Power Switch?

YES

Go to test C

NO

Correct as required

C

Test Motor Function
1.

Remove the front cover of the motor head.

2.

Disconnect the red and black wires from the module to the
terminals inside the rear cover.

3.

Attach jumper leads to the emergency terminals located
on the back of the motor head.

4.

Connect the other ends of the jumpers to a 12-18VDC
power source (i.e. drill battery). It may be necessary to try
then reverse the leads on the battery and try again.

5.

Does the motor run?

YES

Motor is good, go to test D

NO

Motor is defective - replace

D

Test Power Switch
1.

Disconnect wires from Power Switch.

2.

Using a continuity tester place one lead on each terminal.

3.

With the switch in the OFF position, circuit should be
open.

4.

With the switch in the ON position, circuit should be
closed.

YES

Switch is good, go to test E

NO

Switch defective - replace switch
assy.

E

Test the Extend/Retract Switch
1.

Using a continuity tester, place one lead on center pin. Place
the second lead on bottom pin. Put the switch in the center
position and measure the continuity. Circuit should be open.

2.

Press the switch down (Extend). Circuit should be open.

3.

Press the switch up (Retract). Circuit should be closed.

4.

Move the second lead to the top pin. Put the switch in the
center position and measure. Circuit should be open.

5.

Press the switch down (Extend). Circuit should be closed.

6.

Press the switch up (Retract). Circuit should be open

YES

Switch is good, go to test F

NO

Switch defective - replace switch
assy.

F

Test wire continuity between motor and wire ends.

YES

Wire continuity good – module is
defective replace

NO

Repair as required then reconnect
the wires.

«
...
14
15
16
17
18
...
»

Содержание TRAVEL'R ADJUSTABLE PITCH

















































Отзывы:

Нет отзывов