Carefree TRAVEL'R ADJUSTABLE PITCH Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 48

Carefree TRAVEL'R ADJUSTABLE PITCH Скачать руководство пользователя страница 43

T

RAVEL

'

R

P

ATIO

A

WNING

O

PERATING THE

C

ONTROLS



Turn the Power switch ON.



Use the Patio switch to extend or retract the awning as desired.



Set the Sensitivity switch to the level desired.

T

ESTING THE

D

IRECT

R

ESPONSE

S

YSTEM

It is important to test the Direct Response system periodically to ensure that the
system is working properly. Follow the simple test below.

1.

Extend the awning completely.

2.

Set the motion sensitivity to the lowest setting.

3.

Gently move the roller tube up and down in a vertical motion.

4.

If the awning retracts, the system is working properly.

5.

If the awning does not retract, contact an authorized Carefree dealer for repairs.
Operate the awning with the Patio switch until the system is repaired.

U

SING THE

K

EY

FOB

R

EMOTE

C

ONTROL

A remote control Key FOB is available only with the auto-retract
system. The remote provides the advantage of allowing you
to operate the awning from any convenient location.

The remote has a maximum operating range of 50 feet. Actual
distance may vary depending on the specific installation and
location of the receiver in the vehicle.

To use: turn system power ON at the control panel.

NOTE:

Power ON/OFF and the Auto-Retract sensitivity can only

be operated at the control panel.

Extend

Press and release. The awning will extend out to the full extension and stop

automatically.

Retract

Press and release. The awning will retract and stop automatically when the

awning is fully retracted.

Stop

Press and release. During extend and retract functions, the awning may be
stopped by pressing this button.

K

EY

FOB

B

ATTERIES

The Key FOB w/ antenna uses a battery (Radio Shack p/n 23-279 or equivalent)
that should provide a long period of service. To access: Remove the small screw
from the back of the case and carefully snap off the back. Lift the old battery out
and insert the new battery.

Batteries are available through your local battery outlets.

Battery life is dependent on frequency of use, environmental conditions and
condition of remote.

Function

Buttons

Stop

DR010

«
...
41
42
43
44
45
...
»

Содержание TRAVEL'R ADJUSTABLE PITCH

















































Отзывы:

Нет отзывов