manualshive.com logo in svg

Carefree TRAVEL'R ADJUSTABLE PITCH, Руководство по обслуживанию, Страница: 24 / 48

Поделиться
Скачать
Carefree TRAVEL'R ADJUSTABLE PITCH Скачать руководство пользователя страница 24

Carefree of Colorado Service 

Manual 

T

RAVEL

'

R

 

052540-301r10 

21 

M

ANUAL 

O

VERRIDE

 

If the original power source fails or is unavailable, the Travel'r has emergency override terminals (12V). The 
terminals can be used with a 10V-14V power source, such as a cordless drill battery or car battery.  

WARNING  

D

O NOT CONNECT THE 

T

RAVEL

'

R WIRES TO A 

110V

 POWER SOURCE

!

   

D

OING SO WILL 

PERMANENTLY DAMAGE THE AWNING

! 

Travel'r models built through 2012 have override terminals on the back of the motor head.  If the motor 
head has the metal terminals, use the procedure "Override with Emergency Terminals".  For models built in 
2013 and later, use "Override without Emergency Terminals". 

Override With Emergency Terminals 

CAUTION

   

Do not use the emergency terminals without following the directions below.  The 

electronic circuit creates a dynamic brake for the motor by shorting and grounding the motor leads.  
Steps 1 and 2 removes the brake to allow the emergency override to work. 

1. 

(Detail A)

  Remove the front cover from the motor head.  There are six (6) small screws in the rear of 

the motor head. 

2. 

(Detail B)

  Disconnect the input cable 

wires from the terminals in the rear 
cover.  D

O NOT

 disconnect the wires to 

the motor. 

3.  Leave the wires disconnected and 

reattach the front cover. 

4. 

(Detail C)

  Attach the provided jumper 

leads to the terminals, located on the rear 
of the motorized head.  

5.  Connect the other ends of the jumper 

leads to a 12V source.  If the awning does 
not begin to move, reverse the leads. 

6. Maintain contact throughout the 

retraction process. 

CAUTION

  

Be careful when retracting the awning as the awning may move abruptly. 

Override Without Emergency Terminals 

1.  Locate and separate the quick disconnects located in the motor arm 

channel.  Position the wires from the motor on the outside of the 
channel. 

2.  Attach jumper wires to the wires from the motor. 

3.  Connect the other ends of the jumper leads to a 12-14V source.  If 

the awning moves in the wrong direction, reverse the leads.  

4.  Maintain contact throughout the retraction process.  Hold the wires 

from the motor on the outside of the channel while the awning is 
closing.  This will provide access to open the awning. 

CAUTION

   

Be careful when retracting the awning as the 

awning may move abruptly. 

5.  When power is restored, use the jumper wires and extend the awning 

to access the cable disconnects.  Reattach the disconnects and 
secure in the arm channel. 

Quick Disconnects

Located in Arm Channel

TravelR061

Hold Wires

Outside of Channel

When Arm is Closing

Awning

Closed

DO NOT 
Disconnect
Wires to Motor

Disconnect

Input Wires

From Rear

Cover

Travelr044

Motor

Front Cover

DETAIL

 A

DETAIL

 B

Emergency

Terminals

DETAIL

 C

Содержание TRAVEL'R ADJUSTABLE PITCH

















































Отзывы:

Нет отзывов