Carefree LATITUDE Скачать руководство пользователя страница 7

Страница: 7 / 20

Carefree of Colorado Service

Manual

ATITUDE

070005-301r5

8.4. At the reinforcements in the canopy, secure the fabric to the roller tube with the retaining screws

removed previously.

9. While firmly pressing the roller tube, remove the arm ties. Slowly allow the roller tube and arms to extend.

10. Restore power.

11. Retract the awning and check that the canopy is rolling up squarely onto the roller tube. Adjust as

necessary.

12. Place one (1) #6 x 3/8" screw (a) through the QuicKonnect (or awning rail if the QuicKonnect is not

used), fabric and polyrod approximately 1" in from the fabric edge

13. On the opposite side, pull the fabric tight then place one (1) #6 x 3/8" screw (b) through the

QuicKonnect (or awning rail if the QuicKonnect is not used), fabric and polyrod approximately 1" in from
the fabric edge.

14. Connect the LED harness:

14.1. At the roller tube, connect the canopy harness connector and LED connector. Then carefully

push the connectors into the roller tube.

14.2. Place the split grommet over the canopy harness and press the grommet into the hole of the

roller tube.

14.3. At the vehicle wall, route the new canopy harness through the wall to the switch.

Tip: Tie the new harness to the old harness that was cut previously. Use the old harness to pull
the new harness through the wall to the desired location.

14.4. At the vehicle wall, provide some slack between the canopy and wall. Seal the wall entrance

hole and harness with a quality silicone sealant.

14.5. Connect the new harness to the switch. Two (2) .187, 18-24 awg female disconnects are provided if

connecting to a switch.

14.6.

Alternate method:

At the wall, splice the new harness to the existing harness using 24 awg butt

connectors. Push the connectors into the vehicle wall. Seal the wall entrance hole and wires
with a quality silicone sealant.

NOTE:

Be sure to allow enough harness from the canopy to provide some slack for the harness

and adequate length for the connectors to be pushed inside the wall before sealing the hole and
harness with a quality silicone sealant.

Содержание LATITUDE





















Результаты поиска

Содержание LATITUDE

Отзывы:

Похожие инструкции для LATITUDE

Бренды по названию

Популярные бренды

Carefree LATITUDE, Руководство по обслуживанию

Результаты поиска

Содержание LATITUDE

Отзывы:

Похожие инструкции для LATITUDE

Бренды по названию

Популярные бренды