Carefree LATITUDE Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

background image

L

ATITUDE

Service

Manual

Carefree of Colorado

10

070005-301r5

S

ENSOR

/C

ONTROL

M

ODULE

R

EPLACEMENT

This procedure may be done with the awning open or closed.

1. Disconnect power to the awning.

2. Remove the front cover. The cover snaps onto the rear

cover. To remove, press the bottom of the rear cover until
the front cover releases then lift the front cover off. Set part
aside.

3. Slide the sensor module out of the rear case. Disconnect

the wires to the module.

4. Connect the motor and cable wires to the new module.

Make sure to match the wire colors.

5. Slide the new module into the rear cover and tuck the wires.

6. Snap the front cover onto the rear cover. Hang the cover on

the top and swing down until it clicks.

7. Restore power and test.

Front Cover

Module

FL019

Wires to
Motor

Cable to
Module

«
...
12
13
14
15
16
...
»

Содержание LATITUDE





















Отзывы:

Нет отзывов

Похожие инструкции для LATITUDE

Бренд: Palm Страницы: 14

Бренд: Toco Страницы: 12

I-Class Mark II

Бренд: Datamax Страницы: 12

SuperStack 3 4300

Бренд: 3Com Страницы: 8

Бренд: 3B Medical Страницы: 7

Бренд: Abicor Binzel Страницы: 8

Бренд: FeiYu Tech Страницы: 34

Бренд: Hard Head Страницы: 40

Бренд: Harbor Freight Tools Страницы: 7

Бренд: Racing Страницы: 13

Бренд: Farad Страницы: 8

PERFECTVIEW CAM80AHD

Бренд: Dometic Страницы: 196

Бренд: eufy Security Страницы: 12

Drive Pro EZ Build 41130

Бренд: Meyer Страницы: 11

Бренд: White Outdoor Страницы: 4

Бренд: BESAFE Страницы: 4

Бренд: Transcend Страницы: 64

Бренд: DrBrowns Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды