18
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5 Volts Negative Ground
Trigger Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grounded Pin Switch, Positive Pin Switch,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic Sensor Ground, 0.6 Volt Current Drop
Current Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Less Than 15mA Armed or Disarmed
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programmable Automatic Arming Timer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programmable Rearming Timer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Second RF Tamper Rearming Timer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Second Zone Bypass Re-Activation Timer
Grounded Output Wire Capacity (White Wire) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA
Siren Output Wire Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Amps
Channel 2 Pulsed Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mA
Bypass Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Zones
Transmitter Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434mHz
Digital Code Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68,000,000,000
Code Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital Code Hopping
Transmitter Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No More than 4
Ignition Controlled Door Locking:
(Door lock activation must be installed)
When programmed on in “Remote Feature Programming”, ignition controlled locking is active 3 seconds
after the ignition key is set the On position, the door locks will automatically become locked. When the
ignition key is turned to the Off position, the door locks will unlock.
Note: If a protected entrance (door) is opened when the ignition key is set to the On position, the door
locks will not lock. This protective measure can not be deleted.
Channel #2 Output:
(If Installed)
Press and hold the Channel 2 activation button (
*
) for 2 seconds. The designated Channel 2 output
wire from the alarm will become grounded for as long as the (
*
) button is pressed.
Dual-Zone Sensor Pre-Warning Indicator:
(If Installed)
1. Close all protected entrances and place the alarm in an armed condition.
2. Rap the vehicles body panels to activate the pre-warning zone of any dual-zone type sensor.
3. When the pre-warning indicator is triggered, the horn/siren will beep 1 time.
Step 8: Speciality Feature and Optional Equipment Testing
Specifications
