SIMPLE™ KEY USER GUIDE
SIMPLE™ KEY USER GUIDE
14
15
FREQUENTLY ASKED QUESTIONS
Q:
The EZ Installer™ beeps 5 times after pushing the button to initiate the pairing process and will not pair the new key.
A:
Your vehicle allows a maximum of 5 paired keys or 6 paired remotes. If the vehicle already has 5 keys paired to it, a new key
cannot be paired. If the EZ Installer™ beeps 5 times early in the pairing process, this indicates that the maximum number of keys
have been paired. Perform both the ERASE KEY and ERASE REMOTE steps. Then, try the KEY PAIRING and REMOTE PAIRING
processes again. Gray colored valet keys should be paired before black master keys or remotes.
Q:
Can I use the same EZ Installer™ on other vehicles?
A:
No, the EZ Installer™ will be locked to the first vehicle it is used on. You may add more keys to the same vehicle again as
needed, but it will not work on different vehicles. If the EZ Installer™ sounds 3 beeps at 1 second intervals, then beeps rapidly, this
signifies that the device has already been used on another vehicle. Visit CKESimpleKey.com or your local retailer to purchase
additional key.
Q:
The EZ Installer™ sounds 3 or 4 beeps at 1 second intervals 3 times then beeps continuously.
A:
When problems occur during the pairing process, EZ Installer™ will beep an error code, followed by continuous faster beeps.
The number of error beeps correspond to specific error codes, explained below.
•
Three
distinct beeps at 1 second intervals indicate the device has already been used on another vehicle. The EZ Installer™
can only pair Simple™ Keys to one vehicle. The EZ Installer™ will be locked to the first vehicle it is used on. You may add
more keys to the same vehicle again as needed, but it will not work on different vehicles.
•
Four
distinct beeps at 1 second intervals indicate that the incorrect dial position was selected on the EZ Installer™. Carefully
read the instructions and refer to the compatibility lookup on pages 4-5.
Please contact Car Keys Express customer service at 888-598-8910 for any questions.
Q:
The new key won’t pair to my car.
A:
If the EZ Installer™ doesn’t pair the key to your car, most likely an incorrect dial position was used. In this case,
the EZ Installer™ will beep continuously after you press the pairing button. Check the compatibility section on
pages 4-5 to confirm the correct dial position for your make, model, year, and transponder chip of your original
key. If an alternate dial position(s) is listed for your vehicle, unplug the EZ Installer™, turn the knob to the alternate
position, and try pairing again. If the key still won’t pair, please contact customer service at 888-598-8910.
Q:
The EZ Installer™ was unplugged during the pairing process.
A:
The EZ Installer™ must remain plugged into the on-board diagnostic (OBD) port until pairing is complete. If the
EZ Installer™ becomes unplugged during the pairing process, turn the ignition to the OFF position, remove the
key, and begin the pairing process again.
Q:
The vehicle won’t start with the new key or old keys after attempting to pair.
A:
Please call Car Keys Express customer service at 888-598-8910.
FCC AND ISED REGULATORY STATEMENT
MODEL: RT-TOY-A or 12BBY
MODEL: RT-TY54B or 12BDM
FCC ID: 2AOKM-TOY-V1 or HYQ12BBY
FCC ID: 2AOKM-TY5 or HYQ12BDM
IC: 24223-TYV1 or 1551A-12BBY
IC: 24223-TY5 or 1551A-12BDM
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
TRANSPONDER CHIP: DOT
TRANSPONDER CHIP: H
