Car-Interface CI-RL4-MBN6 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 26

background image

Version 22.10.2021

HW:CAM(V98/99/100)/(V45/46)

CI-RL4-MBN6

P

a

g

e

9

2.1.2.

Place of installation - RL4-MBN6

The installation of the interface box close to or behind the MBUX head unit should generally be
avoided in all vehicles due to thermal problems, as the head-unit has a very high heat generation.
Particularly in the Sprinter W907/910 in the area around the MBUX head unit exists high heat
generation due to solar radiation and the heating pipes. For the Sprinter W907/910, it is
recommended to install the video interface in the centre console below the MBUX system, as shown
in the pictures.

«
...
7
8
9
10
11
...
»

Содержание CI-RL4-MBN6



























Отзывы:

Нет отзывов

Похожие инструкции для CI-RL4-MBN6

Бренд: ECO Sensors Страницы: 2

Бренд: Napoleon Страницы: 4

Бренд: hager Страницы: 4

Бренд: Laser Страницы: 8

Бренд: Manfrotto Страницы: 2

Бренд: Warmon Страницы: 2

1973 Convertible

Бренд: Volkswagen Страницы: 80

Бренд: TERSUS Страницы: 27

Бренд: Lanics Страницы: 23

Бренд: Olympus Страницы: 171

Бренд: RAM Страницы: 496

Бренд: SUPAIR Страницы: 30

Бренд: Navig8r Страницы: 10

Бренд: Foxtech Страницы: 26

Mach 3 GL Series

Бренд: Balboa Instruments Страницы: 2

Бренд: Ammonite System Страницы: 8

Бренд: IMI SENSORS Страницы: 21

Бренд: Ikelite Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды