Car-Interface CI-RL4-MBN6 Скачать руководство пользователя страница 7

Страница: 7 / 26

Version 22.10.2021

HW:CAM(V98/99/100)/(V45/46)

CI-RL4-MBN6

1.5.

Settings - 6 Dip switches (Top of box–black)

The 6 dip switches at the top of the video interface are
responsible for the according monitor assignment.

Attention: In contrast to both other dip benches (8dip and
4dip),
the 6dip position

UP = ON

and

DOWN = OFF

Monitor

size

Dip 1

Dip 2 Dip 3 Dip 4 Dip 5 Dip 6

7inch monitor
Sprinter (W907/910)
GLC (X253)

OFF

7”inch monitor
A-Class (W177)

B- Class (W247)

CLA Coupé (C118)

CLA Shooting B (X118)

GLA (H247)

GLB (X247)

OFF

10.25 inch monitor
Sprinter (W907/910)
A- Class (W177)
B- Class (W247
CLA Coupé (C118)
CLA Shooting B (X118)
EQC (N293)
GLA (H247)
GLB (X247)
GLC (X253)
GLE Coupé (C167)
GLE SUV (W167)
GLS- Class (X166)

OFF

Complete list of vehicle model and year – see page 4

*If there is a malfunction in vehicles with 7 inch monitor, try also the other dipswitch settings!

After each Dip-switch-change a power-reset of the interface-box has to be performed!

1.6.

Settings of the 4 Dip switches (CAN functions – red)

All 4 dip-switches of the video interface have no function for
normal use and have to be set to OFF.

Dip position

UP = OFF

and

DOWN = ON

Vehicle/Navigation

Dip

Dip 2

Dip 3

Dip 4

All vehicles

OFF

Vehicles with factory park pilot system

OFF

Hinweis: Während Nutzung von Parkpilotsystemen ist kein Rückfahrkamerabild verfügbar

After each Dip-switch-change a power-reset of the interface-box has to be performed!

Содержание CI-RL4-MBN6



























Результаты поиска

Содержание CI-RL4-MBN6

Отзывы:

Похожие инструкции для CI-RL4-MBN6

Бренды по названию

Популярные бренды

Car-Interface CI-RL4-MBN6, Руководство пользователя

Результаты поиска

Содержание CI-RL4-MBN6

Отзывы:

Похожие инструкции для CI-RL4-MBN6

Бренды по названию

Популярные бренды