Caple PH501E Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

Caple PH501E Скачать руководство пользователя страница 6

Instruction manual PH501E

Please keep this instruction manual for future reference

6

FITTING INSTRUCTIONS

The plinth heater pack contains the following items:

1 x Heater unit
1 x Stainless steel fascia grille with fixing screw pack
1 x Wall controller
1 x Instruction manual

Location

Select a location in a cavity beneath a kitchen cupboard ensuring the area is clean
and level. Care should be taken not to store perishable goods in the cupboard
directly above the heater.

NOTE:

This plinth heater must not be fitted in a bathroom or other high humidity area.

Preparation

This product is normally fitted directly onto the floor. Once the position has been
decided, mark out and cut the plinth to the dimensions as shown below. Please
take care to make the cut out sizes as accurate as possible as the grill is 100m high.

It is recommended that a gap of 20mm is left between the top of the plinth and the
shelf of the cupboard above to ensure adequate airflow

A

B

Floor mounting

Plinth mounting

A = Width of cut out
B = Height of cut out

A

B

A

B

360mm

96mm

PH501E Instruction manual.indd 6

16/07/2018 13:44

«
...
4
5
6
7
8
...
»

Содержание PH501E

















Отзывы:

Нет отзывов