Canon Super G3 FAX Board-AR1, Руководство по обслуживанию

Страница: 30 / 69

5
5
Service Mode
Service Mode
5-8
5-8
Service Mode > Setting of Bit Switch (SSSW) > Bit Switch Composition > SSSW-SW14
Service Mode > Setting of Bit Switch (SSSW) > Bit Switch Composition > SSSW-SW14
■
SSSW-SW12
● Functional Construction
Bit Function 1 0
0 Time-out period for one page upon transmission 1 0
1 Time-out period for one page upon transmission 1 0
2 Time-out period for one page upon (HT transmission) 1 0
3 Time-out period for one page upon (HT transmission) 1 0
4 Time-out period for one page upon reception 1 0
5 Time-out period for one page upon reception 1 0
6 not used - -
7 Respective page timer settings for transmission and for reception enable do not enable
The machine will stop the ongoing communication if the transmission/reception of a single
original page takes 32 min or more. To use the timer for a purpose other than this function,
refer to the tables that follow, and select an appropriate time length.
When 'do not enable' is selected using bit 7, the time-out length for a single page for all
modes will depend on the setting of bit 0 and bit 1.
Time-Out Length for Transmission/Reception
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
8 min 0 * * * * * 0 0
16 min 0 * * * * * 0 1
32 min 0 * * * * * 1 0
64 min 0 * * * * * 1 1
Time-Out Length for Transmission (in text mode)
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
8 min 1 * * * * * 0 0
16 min 1 * * * * * 0 1
32 min 1 * * * * * 1 0
64 min 1 * * * * * 1 1
Time-Out Length for Transmission (image mode other than text mode)
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
8 min 1 * * * 0 0 * *
16 min 1 * * * 0 1 * *
32 min 1 * * * 1 0 * *
64 min 1 * * * 1 1 * *
Time-Out Length for Reception
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
8 min 1 * 0 0 * * * *
16 min 1 * 0 1 * * * *
32 min 1 * 1 0 * * * *
64 min 1 * 1 1 * * * *
T-5-7
T-5-8
T-5-9
T-5-10
T-5-11
■
SSSW-SW14
● Functional Construction
Bit Function 1 0
0 not used - -
1 not used - -
2 direction of scanning for inch/mm
conversion
both main and sub
scanning directions
sub scanning
direction only
3 not used - -
4 inch-configuration resolution declaration declare do not declare
5 not used - -
6 not used - -
7 not used - -
Detailed Discussions of Bit 2
Use it to specify whether to convert or not convert an inch-configuration resolution into a
millimeter-configuration resolution for image read in G3 transmission: either in sub scanning
direction only or in both main and sub scanning directions. The setting is valid only when bit 1
of SW05 of #1 SSSW is set to '1'.
Detailed Discussions of Bit 4
Use it to specify whether to declare or not declare an inch-configuration resolution to the other
machine for G3 communication: if 'declare' is selected, the machine will indicate that it reads
and records at an inch-configuration resolution using the DIS, DCS, or DTC signal.
T-5-12