Canon PIXMA MX340 Series Скачать руководство пользователя страница 5

Страница: 5 / 35

(4/37)

Error

code

U No. Message on the LCD

Solution

Parts that are likely to be

faulty

No ink (no raw

ink).

[1688] U163 Ink has run out.

Replace the ink

cartridge.

Replace the empty ink

cartridge(s). Printing with an

empty ink cartridge can

damage the printer.

To continue printing without

replacing the ink

cartridge(s), press the Stop

button for 5 sec. or longer to

disable the function to detect

the remaining ink amount.

After the operation, it is

recorded in the printer that

the function to detect the

remaining ink amount was

disabled.

- Ink cartridge

- Logic board

Warning: The ink

absorber

becomes almost

full.

[1700] --- The ink absorber is

almost full.

Replace the ink absorber,

and reset its counter. (See

2-1, Service Mode.)

Pressing the STOP button

will exit the error, and enable

printing without replacing the

ink absorber. However,

when the ink absorber

becomes full, no further

printing can be performed

unless the applicable ink

absorber is replaced.

- Ink absorber kit

The connected

digital camera or

digital video

camera does not

support Camera

Direct Printing.

[2001] --- Incompatible device

detected.

Remove the device.

Remove the cable between

the camera and the printer.

- PictBridge harness

- Logic board

Non-supported

hub

[2002] --- An unsupported USB

hub is connected.

Remove the hub.

Remove the applicable USB

hub from the PictBridge

(USB) connector.

- PictBridge harness

- Logic board

Paper jam in the

ADF

[2801] --- Document in ADF.

Redo operation after

checking document in

ADF and pressing

[OK].

Remove the jammed paper

from the ADF, press the OK

button, then perform the

operation again.

- Document upper guide

unit

No paper in the

ADF

[2802] --- No document in ADF.

Press [OK] and redo

operation after setting

document.

Press the OK button, set the

document in the ADF, and

perform the operation again.

- Document upper guide

unit

The paper in the

ADF is too long.

[2803] --- Document is too long.

Press [OK] and redo

operation.

Press the OK button, and

perform the operation again.

- Document upper guide

unit

Содержание PIXMA MX340 Series




































Результаты поиска

Содержание PIXMA MX340 Series

Отзывы:

Похожие инструкции для PIXMA MX340 Series

Бренды по названию

Популярные бренды

Canon PIXMA MX340 Series, Упрощенное руководство по обслуживанию

Результаты поиска

Содержание PIXMA MX340 Series

Отзывы:

Похожие инструкции для PIXMA MX340 Series

Бренды по названию

Популярные бренды