manualshive.com logo in svg

Canon PIXMA MP970, Руководство по обслуживанию, Страница: 8 / 88

Поделиться
Скачать
Canon PIXMA MP970 Скачать руководство пользователя страница 8

*1:  Only for models supporting CD / DVD printing 

*2:  Only for models not supporting CD / DVD printing

the same color 
installed.

following color is installed.

(s).

Ink tank in a wrong 
position.

[1680]

U072 Some ink tanks are not installed in 

place.

Install the ink tank(s) in the correct position.

Warning:  The ink 
absorber becomes 
almost full. 

[1700, 1701]

---

Contact the support center or 
service center for ink absorber 
replacement. Press [OK] to 
continue printing. 

Replace the ink absorber, and reset its counter. [See

3-3. Adjustment / Settings, (6) Service mode.

] 

Pressing the OK button will exit the error, and 
enable printing without replacing the ink absorber. 
However, when the ink absorber becomes full, no 
further printing can be performed unless the 
applicable ink absorber is replaced. 

The connected 
digital camera or 
digital video camera 
does not support 
Camera Direct 
Printing. 

[2001]

---

The device may be incompatible. 
Remove the device and check the 
manual supplied with the 
connected device. 

Remove the cable between the camera and the 
machine.

Automatic duplex 
printing cannot be 
performed. 

[1310]

---

This paper is not compatible with 
duplex printing. Remove the 
paper and press [OK]. 

The paper length is not supported for duplex 
printing. 
Press the OK button to eject the paper being used at 
error occurrence. 
Data which was to be printed on the back side of 
paper at error occurrence is skipped (not printed). 

Failed in automatic 
print head alignment. 

[2500]

---

Auto head align has failed. Press 
[OK] and repeat 
operation. <See manual> 

Press the OK button to clear the error, then perform 
the automatic print head again. 
(In the MP610, use Matte Photo Paper MP-101.) 

The remaining ink 
amount unknown. 

[1683] 

U130  (Applicable ink tank icon) 

The remaining level of the 
following ink cannot be correctly 
detected. Replace the ink tank. 

An ink tank which has once been empty is installed. 
Replace the applicable ink tank with a new one. 
Printing with a once-empty ink tank can damage the 
machine.  
To continue printing without replacing the ink tank
(s), press the Stop/Reset button for 5 sec. or longer 
to disable the function to detect the remaining ink 
amount. After the operation, it is recorded in the 
machine EEPROM that the function to detect the 
remaining ink amount was disabled. 

Ink tank not 
recognized. 

[1684]

U140 The following ink tank cannot be 

recognized.  
(Applicable ink tank icon) 

A non-supported ink tank is installed (the ink tank 
LED is turned off). Install the supported ink tanks.

Ink tank not 
recognized. 

[1410 to 1419]  U150  The following ink tank cannot be 

recognized.  
(Applicable ink tank icon) 

A hardware error occurred in an ink tank (the ink 
tank LED is turned off). Replace the ink tank(s). 

No ink (no raw ink). 

[1688] 

U163  The following ink has run out. 

Replace the ink tank.  
(Applicable ink tank icon) 

Replace the empty ink tank(s), and close the 
scanning unit (printer cover). 
Printing with an empty ink tank can damage the 
machine. 
To continue printing without replacing the ink tank
(s), press the Stop/Reset button for 5 sec. or longer 
to disable the function to detect the remaining ink 
amount. After the operation, it is recorded in the 
machine that the function to detect the remaining 
ink amount was disabled.

Non-supported hub 

[2002] 

--- 

An unsupported USB hub is 
connected. Remove the hub. 

Remove the applicable USB hub from the 
PictBridge (USB) connector.

Unable to release 
Scanner lock switch. 

[5020] 

--- 

Release the scanner lock switch 
and turn the power off and back 
on. 

Unlock the scanner lock switch, turn the machine 
off, then turn the machine on again.

6 / 45

Содержание PIXMA MP970

























































































Отзывы:

Нет отзывов