Canon MF724Cdw Скачать руководство пользователя | Manualshive

Страница: 35 / 327

background image

■ Open door detection

This product detects door opening by the door open sensor.

Sensor Name

Function

Front Cover Sensor (SR612)

Detect open the Front Cover.

Rear Cover Sensor (SR613)

Detect open the Rear Cover.

When this sensor detects door opening, the DC controller stops driving motors and solenoids.

■ Low-Voltage Power Supply Control

This circuit converts AC voltage input from the power supply receptacle through the fixing power supply into DC power supply
and supplies it to each load.
See the figures below for low-voltage / fixing power supply block diagrams.

• Low-voltage power supply: generates DC power supply required in the printer.
• Fixing power supply: supplies AC power supply to the low-voltage power supply and control the fixing heater temperatures.

The low-voltage power supply is actuated when the AC power supply is attached to the inlet and the power switch is turned on.
The AC power supply supplied through the fixing power supply is converted to + 24V and + 3.3V of the DC power supply in the
low-voltage power supply before supplied to the printer engine.

Noise Filter

Fuse
FU1101

Fuse
FU1102

Fuse
FU1201

Fixing Power Supply

Rectifying

Circuit

Main

Controller PCB

3.3V

24S_ON

24V

Low-voltage Power
Supply (all night)

Power
Switch
SW1

DCON_ON

24V DCON

24V REM
3.3V DCON

AC input

Protection

Circuit

Frequency

Detecting

Circuit

㼆㻱㻾㻻㼄

Noise Filter

Fixing
Control
Circuit

Controller PCB

+24V

Generation

Circuit

+3.3V

Generation

Circuit

DC

■ Protective control

The low-voltage power supply has protective controls against excessive current and voltage, which automatically detect excessive
current or abnormal voltage to shut off the output voltage for avoiding the power supply circuit failures.
In case the DC voltage output is not detected from the low-voltage power supply, the protective control may be activated. Turn
off the power switch and remove the AC power supply from the inlet to settle load troubles. Once these are settled, turn on the
power switch again.
Another protective control is provided by 2 power fuses on the fixing power supply. These are open when excessive current is
detected to shut off power supply to low-voltage power supply.

■ Power-Saving Mode

This is the function to save power consumed by the printer.
The table below lists various power-saving modes.

2. Technical Explanation

27

«
...
33
34
35
36
37
...
»

Содержание MF724Cdw








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MF724Cdw

Бренд: TE Connectivity Страницы: 2

Бренд: TE Connectivity Страницы: 2

Бренд: Ricoh Страницы: 2

Бренд: Parkside Страницы: 176

Бренд: MAC TOOLS Страницы: 2

Бренд: Konica Minolta Страницы: 404

ECOSYS P8060cdn

Бренд: Kyocera Страницы: 20

Бренд: Lexmark Страницы: 2

Бренд: Samsung Страницы: 17

Бренд: DataCard Страницы: 2

Бренд: Infotec Страницы: 195

Бренд: Muratec Страницы: 6

Pacemark PM4410

Бренд: Oki Страницы: 28

Бренд: Epson Страницы: 10

Бренд: Mitsubishi Electric Страницы: 24

Бренд: Mitsubishi Electric Страницы: 2

Бренд: Mitsubishi Electric Страницы: 25

Бренд: Mitsubishi Electric Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды