Canon DR-4010C - imageFORMULA - Document Scanner страница 28 Скачать руководство пользователя

Страница: 28 / 143

Chapter 2

Setup

2-12

Connect the power cord into an AC outlet.

Use the supplied USB cable to connect the scanner to the computer.

Using a SCSI Connection

IMPORTANT

• Make sure that the computer is turned OFF before connecting the SCSI cable. If the cable is

connected while the computer is on, the scanner may not be properly recognized by the

computer.

• A SCSI cable is not supplied with the scanner. Purchase a cable that is suitable for the

scanner and for the SCSI connector on the computer.

• The SCSI ID of the scanner is set to “SCSI ID = 2” by default. When using a daisy-chain

configuration with other SCSI devices, set the DIP switches so that there is no duplication of

SCSI ID numbers in the system.

• The DR-4010C scanner incorporates a SCSI terminator which is permanently set to ON.

When using a daisy-chain configuration with other SCSI devices, make sure that the DR-

4010C is connected as the last device in the chain. Set the terminators of all other devices

to OFF.

Type A

Type B

symbol on plug should face down

DIP switches

Factory default (SCSI ID = 2)

Содержание DR-4010C - imageFORMULA - Document Scanner
















































































































































Результаты поиска

Содержание DR-4010C - imageFORMULA - Document Scanner

Отзывы:

Похожие инструкции для DR-4010C - imageFORMULA - Document Scanner

Бренды по названию

Популярные бренды

Canon DR-4010C - imageFORMULA - Document Scanner, Руководство пользователя

Результаты поиска

Содержание DR-4010C - imageFORMULA - Document Scanner

Отзывы:

Похожие инструкции для DR-4010C - imageFORMULA - Document Scanner

Бренды по названию

Популярные бренды