Canon DADF-P1 Скачать руководство пользователя страница 31

Страница: 31 / 90

Chapter 2

2-9

F-2-18

2.5.2 Operation Sequence

0010-3915

F-2-19

2.6 Document Feeding/Delivery

2.6.1 Basic Operation

0011-2272

After stream reading on the document glass, the document is delivered to the document delivery unit as discussed below.

a. Document feed/delivery

After moving past the reading position, the document is fed by the delivery reversal roller driven by the feed motor (M1) turning in the forward direction. The

deliver reversal motor is normally pressurized; the roller release solenoid turns on only when the document is reversed for duplex printing.

F-2-20

Registration
roller

Read standby point

Read roller

SL1

Delivery reversal roller

Document
reversal

Document's
reverse
side reading

Roller release
solenoid (SL1)

Document
separation
/feed

Document
reading

Image leading
edge signal

Reverse rotation

Forward rotation

Loop formation

Read standby

Start key ON

document pickup

signal input

Document

placement

: Reverse rotation of motor

Document set
sensor (PI11)
Registration paper
sensor (PI8)

Read sensor (PI7)

Delivery reversal
sensor (PI6)

Pickup motor (M2)

Feed motor (M1)

Loop formation

Reversal standby

SL1

Delivery reversal roller

Reading position

SL1

Delivery reversal roller

Содержание DADF-P1



























































































Результаты поиска

Содержание DADF-P1

Отзывы:

Похожие инструкции для DADF-P1

Бренды по названию

Популярные бренды

Canon DADF-P1, Руководство по обслуживанию

Результаты поиска

Содержание DADF-P1

Отзывы:

Похожие инструкции для DADF-P1

Бренды по названию

Популярные бренды