background image

18

125237.PDF

19

73 mm ADAPTER INSTALLATION

The following procedure should only be completed by a professional bike mechanic.   

The adapter IS NOT a repair part 

and will only work in undamaged frames in good condition.

1.   Remove the BB30 bearings and circlips  from the bottom bracket shell. 

2.  Thoroughly clean and dry the inside of the bottom bracket shell.    Remove any grease or dirt.  Use a clean lint-free shop 

towel dampened with alcohol to finish.

3.  Apply Loctite™ 609  carefully to the bearing seat positions on both side of the inside  shell.   

4.    Clean the outer surface of the adapter.  Use a  clean shop towel dampened with alcohol.

5.    The groove side of the adapter must be located on the drive side.  With a headset press, press the ADAPTER until the groove 

side face is flush with the drive side face of the SI BB shell.

 

Allow at least 12 hours (at 72°F) for the Loctite to cure before installing the standard bottom bracket crankset.  

Follow Loctite Technical Data Sheet 

http://tds.loctite.com/tds5/docs/609-EN.PDF

Groove

KP010/

73 mm ADAPTER

DRIVE SIDE

(Headset press not shown)

KF368/

ADAPTER w/TOOL

Loctite™ 609

NOTICE

We strongly recommended that you use a swab to control the application and avoid spillage of the Loctite.  Prolonged contact 
with the frame finish may result in discoloration or damage.  Be sure to immediately wipe up any spills and remove any 
compound in contact with the painted surfaces.

68mm ADAPTER REMOVAL

The following procedure should only be completed by a professional bike mechanic.  

The adapter is removable, how-

ever, repeated removal and reinstallation could result in damage to the SI BB shell and is not recommended.    

1.  Removal of the SI BB ADAPTER is accomplished through the use of the extraction tool 

KF366/

 , a two-piece tool set used with 

a headset bearing press.  The arrangement of the tool parts for removal is shown next figure.

2.  Press the adapter out of the shell using the headset press until the adapter is retained inside the receiver and can be 

withdrawn from the bottom bracket shell.

 

Following removal, it will be necessary to clean  all remaining Loctite residue with a before reinstalling the SI circlips and 
bearings. Use Loctite 768.  Use a dental pick to remove any adhesive from the grooves.  Do not cut, face, or use abrasives to 
clean the inside if the BB shell.   

For Loctite clean-up instructions : 

 

http://tds.loctite.com/

(Headset press not shown)

KF366/

 EXTRACTION TOOL

DRIVE SIDE

Receiver

Press

ADAPTER

NOTICE

Use only  extraction tool  Cannondale 

KF366/

  and a headset press.   Do not use other tools.

Make sure the Receiver part of the tool is centered on the drive side bottom bracket shell  while pressing.

We strongly recommend that your have this procedure performed by an Authorized Cannondale Dealer.  Damage caused by 
improper removal is not covered under your warranty.

Содержание MOTO CARBON
















Отзывы: