background image

13

126560.PDF

Specifications

Frame Types

BallisTec Carbon or SmartFormed Alloy

Headtube

Integrated Si

Chainline

50 mm

BB Shell Width

BB30 73 mm

Rear Travel  Modes (remote lever selectable)

FLOW - 90 mm
ELEVATE - 150 mm

Rear Shock

FOX DYAD RT2 Pull Shock

Seat Post Diameter

Use a seat post with a 31.6 mm diameter only.
Do not use other  size seatposts.  Do not use a seat post with a shim or 
adapter.  Use carbon gel 

KF115/

 when installing a seat post.

Front Derailleur

S3 Direct Mount, Bottom pull     

Dropout Spacing

142mm (convertible to 135mm)

Rear Brake

Post Mount  Adapters - 160/180/185/203

WARNING

Please  read  your 

Cannondale  Bicycle  Owner’s  Manual 

for  more  information  on  the  following  specifications:

Intended Use

ASTM Condition 4, All-Mountain OverMountain

Maximum Tire Width

2.5”

Maximum Fork Length

545 mm

Minimum Seat Post Insert

100 mm

Tightening Torques

Correct tightening torque for the fasteners (bolts, screws, nuts) on your bicycle is very important to your safety.the durability and 
performance of your bicycle.   We urge you to have your Dealer correctly torque all fasteners using a torque wrench.  If you decide to 
tighten fasteners yourself always use a good torque wrench! 

DESCRIPTION

Nm

In Lbs

Loctite™ 

Rear Brake Adapter  (Maximum)

10.0

88.5

242 (blue)

Shock Mounting Bolts

8.0

 71.0

Dropout Pivot Axle Bolts

7.0

62.0

Shock Link Pinch Bolts

5.0

44.0

Main Pivot Pinch Bolts
BB Cable Exit Guide Screws

2.5

22.0

Rear Derailleur Hangar Screws
Housing Guides  (Maximum)

3.0

26.5

Содержание Jekyll





























Отзывы: