18
Selecting the programmes
and special functions
Use in conjunction with programme guide
Setting a programme
Press the On/Off button ; the 5 programme
selection indicator lights start flashing to show
that the machine is waiting for a selection to be
made.
Press the Programme Selection Button and
the indicator light for the heavy wash programme
will start flashing. Set the required programme
by pressing the Programme Selection Button
again within 5 seconds. When then light for the
required programme starts flashing, and when
the audible signal has sounded (if it has not
been deactivated) the programme will start
automatically.
Half load button
By pressing this button it is possible to wash a
small quantity of crockery using only the upper
basket for dishes and cutlery in the bottom
basket.
This reduces energy consumption and requires
a smaller quantity of detergent.
The button reduces the temperature of the
water during the last rinse. This activates a
natural drying process, as with a normal
draining board, simply by leaving the door ajar
at the end of the cycle to enable the natural
circulation of air.
Interrupting a programme
It is not recommended that the door be opened
while a programme is running, and especially
not during the main wash phase and final
drying.
However, the appliance stops automatically
when the door is opened. At this point the
button can be programmed or cancelled.
When the door is closed again, the programme
continues automatically. If you wish to change
or cancel a programme which is running, carry
out the following procedure:
keeping the Programme Selection Button
pressed in until all 5 indicator lights are flashing.
A new setting can now be made.
NB: If, on pressing the Programme Selection
Button
the indicator lights start flashing
alternately, it means that there is water in the
machine.
Release the Programme Selection button
and the machine will automatically empty the
water; wait for the audible signal, after which the
new programme can be set.
Before starting a new programme, you should
check that there is still detergent in the dispenser.
If necessary, top up the dispenser.
End of programme
The end of the programme is indicated by an
audible signal. The 5 programme selection
indicator lights start flashing. Release the
On/Off button.
Activating and Deactivating the audible
signal
The audible signal function can be deactivated
in the following way:
keep the Programme Selection Button
pressed in for a few seconds and at the same
time press the On/Off button; if the three
indicator lights “INTENSIVE programme”,
“DAILY
programme”
and “RAPID 32’
programme” are illuminated, the audible signal
is activated. By pressing the Programme
Selection Button
again, the “UNIVERSAL
programme” and “ECO programme” lights
will come on, which means that the audible
signal has been deactivated. An audible signal
sounds to indicate that the setting has been
stored in memory.
Attention
This dishwasher is equipped with an anti-overflow
safety device which works even when power is
switched off and and if the water level is too high
the supply will automatically be closed off.
Important
To ensure the correct operation of the anti-overflow
safety device, it is recommended not to move or
to tilt the dishwasher during operation.
If it is necessary to move or to tilt the dishwasher,
first make sure the washing cycle is finished and
that no water is left in the tank.
19
Regulating the water softener
with electronic programmer
The water softener can treat water with a hardness level of up to 90°fH (French
grading) or 50°dH (German grading) through 6 settings.
The settings, are listed in the panel below:
The softener unit is set in the factory at level 3 (Indicator light N.3) as this satisfies
the requirements of the majority of users. Regulate the setting of your water softener
unit according to the degree of hardness of your water as follows: keep button
pressed in for a few seconds and at the same time press the On/Off button .
The indicator light of button will start flashing and indicator light N.3 (the factory
setting) will come on. To change the setting, press button . Each time you press
that button, the next indicator light will come on. When the required indicator light
comes on, wait for the audible signal to confirm that the new setting has been stored
in memory.
Level
0
1
2
3
4
5
0-5
6-15
16-30
31-45
46-60
61-90
0-3
4-9
10-16
17-25
26-33
34-50
NO
YES
YES
YES
YES
YES
Indicator light N.1
Indicator light N.1
Indicator light N.2
Indicator light N.3
Indicator light N.4
Indicator light N.5
Water
hardness
°fH
(French)
Water
hardness
°dH
(German)
Use of
regenerating
salt
Water
softener
setting
ON/OFF BUTTON
Pr
I
Pr
1
2
1
2
1
2
Pr
Pr
I
Pr
Pr
I
1
2
1
2
1
2
Pr
1
2
