background image

 

17 

• Use the correct length for the screws which are identified in 
the Installation Guide. 
• In case of doubt, consult an authorized service assistance 
center or similar qualified person.  
 

 WARNING!  

 

•  Failure to install the screws or fixing device in 

accordance with these instructions may result in 
electrical hazards. 

 

•  Do not use with a programmer, timer, separate remote 

control system or any other device that switches on 
automatically. 

  

 This appliance is marked according to the 

European directive 2012/19/EU on Waste Electrical and 
Electronic Equipment (WEEE). 
WEEE contains both polluting substances (which can cause 
negative consequences for the environment) and basic 
components (which can be re-used). It is important to have 
WEEE subjected to specific treatments, in order to remove 
and dispose properly all pollutants, and recover and recycle all 
materials.  
Individuals can play an important role in ensuring that WEEE 
does not become an environmental issue; it is essential to 
follow some basic rules: 
 

 

WEEE should not be treated as household waste; 
 

 

WEEE should be handed over to the relevant collection 
points managed by the municipality or by registered 
companies. In many countries, for large WEEE, home 
collection could be present. 

 
In many countries, when you buy a new appliance, the old one 
may be returned to the retailer who has to collect it free of 
charge on a one-to-one basis, as long as the equipment is of 
equivalent type and has the same functions as the supplied 
equipment.  
 
Appliance designed, tested and manufactured according to: 
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 
62233. 
• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 
5168; EN/IEC 60704-1; EN/IEC 60704-2-13; ISO 3741; EN 
50564; IEC 62301. 
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; 
EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for a 
correct use in order to reduce the environmental impact:  
Switch ON the hood at minimum speed when you start 
cooking and kept it running for few minutes after cooking is 
finished. Increase the speed only in case of large amount of 
smoke and vapour and use boost speed(s) only in extreme 
situations. Replace the charcoal filter(s) when necessary to 
maintain a good odour reduction efficiency. Clean the grease 

filter(s) when necessary to maintain a good grease filter 
efficiency. Use the maximum diameter of the ducting system 
indicated in this manual to optimize efficiency and minimize 
noise. 

By placing the 

  marking on this product, we declare, 

on our own responsability, compliance to all of European 
safety, health and environmental requirements stated in the 
legislation for this product. 

 

Use 

The hood is designed to be used either for exhausting or filter 
version. 
  

 Extraction version 

In this case the fumes are conveyed outside of the building by 
means of a special pipe connected with the connection ring 
located on top of the hood. 
 

 CAUTION

!  

The exhausting pipe is not supplied and must be purchased 
apart. 
Diameter of the exhausting pipe must be equal to that of the 
connection ring. 
 

 CAUTION

 

If the hood is supplied with active charcoal filter, then it must 
be removed. 

Connect the hood and discharge holes on the walls with a 
diameter equivalent to the air outlet (connection flange). 
Using the tubes and discharge holes on walls with smaller 
dimensions will cause a diminution of the suction performance 
and a drastic increase in noise. 

Any responsibility in the matter is therefore declined.  

Use a duct of the minimum indispensable length. 

Use a duct with as few elbows as possible (maximum 
elbow angle: 90°). 

Avoid drastic changes in the duct cross-section. 

  

 Filtration version 

The aspirated air will be degreased and deodorised before 
being fed back into the room. 
In order to use the hood in this version, you have to install a 
system of additional filtering based on activated charcoal. 
  

 

Installation 

The minimum distance between the supporting surface for the 
cooking equipment on the hob and the lowest part of the 
range hood must be not less than 60cm from electric cookers 
and 70cm from gas or mixed cookers. 
If the instructions for installation for the gas hob specify a 
greater distance, this must be adhered to. 

 

Содержание CBP613













Отзывы: