"WARNING"
THIS APPLIANCE MUST BE EARTHED
Fuses and plugs
This appliance should be used only on a
socket with a minimum rating of 13 Amp.
Our ready-fitted plug is already equipped
with a 13 amp fuse which is BS 1362 ASTA approved.
Any replacement should be exactly the same.
If the fuse cover is lost, do not use the plug until it is replaced.
A correct replacement fuse cover (obtainable from your dealer
or Electricity Board) must be the same colour as shown or na-
med on the insert on the base of the plug.
46
Installation in fitted kitchens
Fitting between existing cabinets
The height of the dishwasher, 85 cm., has been designed in order
to allow the machine to be fitted between existing cabinets of the
same height in modern fitted kitchens. The feet can be adjusted
so that correct height is reached.
The laminated top of the machine does not require any particular
care since it is heatproof, scratchproof and stainproof (fig. 5).
The working top can be easily adjusted to line it with the top of
existing cabinets; this is done by moving it by 5 mm. each time up
to a maximum of 25 mm.
To adjust it, unscrew the two screws at the back and fix the top
in the position required (fig. 7).
Underneath existing working top
In most modern fitted kitchens there is only one single working top
under which cabinets and electrical appliances are fitted.
In this case remove the working top of the dishwasher by unscre-
wing the screws under the rear edge of the top (fig. 7).
The height will then be reduced to 82 cm., as scheduled by the In-
ternational Regulations (ISO) and the dishwasher will fit perfectly
under the kitchen working top (fig. 6).
Fitting panels (some models only)
The frames around the door, present only in some models, allow
decorative panels to be fitted, up to 5 mm. thick, and with the
following dimensions:
width 591 mm.
±
1
height 597 mm.
±
1
47
Water connection
The inlet and drain hoses can be directed to left or right.
The dishwasher can be connected to either cold or hot water,
as long as it is no hotter than 60
°
C.
Water pressure must be between 0,08 MPa and 0,8 MPa. If the
pressure is below the minimum consult our service department for
advice.
The inlet hose must be connected to a tap so that the water supply
can be cut off when the machine is not in use (fig.1 B).
The dishwasher is fitted with 3/4" threaded connector (fig. 2).
Connect inlet hose A to water tap B with a 3/4" attachment making
sure that it has been properly tightened.
If calcareous deposits or sand are present in the water, it is
advisable to obtain the appropriate filter, art. 9226085, from the
Service Centre (fig. 3).
The filter D must be inserted between the tap B and the inlet hose
A, remembering to fit the washer C.
If the dishwasher is connected to new pipes or to pipes which have
not been in use for a long time run water through for a few minutes
before connecting the inlet hose. In this way no deposits of sand
or rust will clog up the water inflow filter.
Connecting the outlet hose
The outlet hose should disharge into a standpipe, making sure that
there are no kinks (fig. 4).
The standpipe must not be less than 40 cm. above floor level and
it must have an internal diameter of at least 4 cm. It is advisable to
fit an anti-odour air trap (fig. 4 x).
If necessary the outlet hose can be extended up to 2,6 m, provided
that it is kept at a maximum height of 85 cm. above floor level.
The hose can be hooked over the side of the sink (it must not be
immersed in water, in order to prevent water from being syphoned
back to the machine when this is in operation) (fig. 4 y).
When installing the appliance under a worktop the hose pipe clamp
must be attached to the wall in the highest possible position under
the worktop (fig. 4 z).
Check that there are no kinks in the inlet and outlet hoses.
If it is necessary to lengthen the inlet pipe, an extension pipe can
be fitted.
Содержание A 9002
Страница 1: ...A 9002 Installation Use Maintenance EN NL DE ES ...
Страница 2: ...1 2 3 4 7 597 556 563 5 6 8 ...
