background image

Overview

Features

The Quick Reference Guide (QRG) takes you through the installation and setup of your 
CSPF-100 series power factor controller and helps you to get setup and running as quickly 
as possible. This guide contains only the basic information to operate the relay.

Introduction

CSPF-100, Power Factor Controller is designed for Automatic / Manual control of external 
Capacitor Banks in 3 Phase 4 Wire or 3 Phase 3 Wire LT distribution systems to allow the 
p o w e r   f a c t o r   o f   t h e   i n s t a l l a t i o n   t o   b e   s t a b i l i z e d   t o   t h e   d e s i r e d   v a l u e .

u

  Effective PF control. Up to 12 capacitor banks controllable

u

  Seven segment display for user interface

u

  Auto / Manual operation

u

  Wide range of measuring voltage Input

u

  Measurement & display of line parameters like V, I, P, Q, S, Cos phi & Temperature

u

  Indication of active capacitor bank through LEDs

u

  Wide range of programmable parameter including CT ratio, target Cos phi value, C/K 

 

ratio, capacitor bank switching program etc.

u

  Suitable for various wiring scheme

u

  Protection & indication on abnormal condition such as over/under 

 

compensation, over voltage, over/under current etc.

u

  FAN control output & over temp alarm based on a built-in temp. sensing

u

  Field accessible test mode for relay contact check

u

  Automatic C/K set-up mode

u

  Potential free alarm output on abnormal conditions

Application

u

 

In all in-comers of an Electrical Plant

u

 

Fixed power factor correction for individual load (e.g: Motor, Transformer etc.)

u

 

Hi-tech Software Parks, Buildings and Shopping Malls

The disposal of our products and possible recycling of their components after 
decommissioning has to be carried out by an accredited recycling company 
or the products/components must be taken to applicable collection points. 
Such  disposal  activities  must  comply  with  all  local  laws,  guidelines  and 
environmental specifications of the country in which the disposal is done.

Our products and batteries must not be disposed of as household waste. For disposing 
batteries it is necessary to observe the local national/international directives.
According to national legislation, penalties may be charged for incorrect disposal of such 
waste.
By disposing of these products correctly you will help to save valuable resources and 
prevent any potential negative effects on human health and the environment.

Disposal

02

Содержание CSPF-100

















Отзывы: