Canature WaterGroup Hydrotech 485HE Скачать руководство пользователя | Manualshive

Страница: 1 / 36

background image

/WDKZΘdĞƌƟĮĞĚ

ŐĂŝŶƐƚE^&ͬE^/ϰϰĂŶĚ

^ϰϴϯ͘ϭ

Owner’s Manual

85HE

Water Softener Manual

(For models after June 2022)

1.

This manual contains important safety and operating instructions. Read all instructions and follow

them when using this product. Failure to consider this information and follow these instructions,

including those concerning maintenance, may result in property damage, injury and or death.
Page 27 of this manual contains important maintenance procedures for the continued proper

operation of your unit. These MUST be performed regularly for your warranty to remain valid.

2.

We recommend installation only be completed by a competent installer or plumbing professional to insure this

product is installed in accordance with local plumbing codes.

3.

Read this manual in full and follow all instructions carefully before operation.

4.

Avoid pinched O-rings during installation by applying NSF certified lubricant to all seals (provided with install kit).

5.

This system is not intended for treating water that is microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system.

6.

Discard small parts remaining after the installation.

7.

Failure to install the system correctly voids the warranty.

8.

Handle all components of the system with care. Do not drop, drag or turn components upside down.

9.

Save these instructions and keep track of your product’s serial number.

NOTICE: THIS MANUAL CONTAINS A LIMITED WARRANTY. BY INSTALLING AND OR USING THIS PRODUCT, YOU WAIVE
CERTAIN LEGAL RIGHTS INCLUDING THE RIGHT TO SUE OR CLAIM COMPENSATION IN THE EVENT OF PROPERTY

DAMAGE, INJURY, AND OR DEATH.

Canature WaterGroup Canada Inc.

855 Park St., Unit 1

Regina, SK, S4N 6M1

Toll Free: (877) 288-9888

Canature WaterGroup U.S.A. Inc.

6353 Commerce Drive

Whitestown, IN, 4607

Toll Free: (877) 288-9888

1
2
3
...
»

Содержание Hydrotech 485HE





































Отзывы:

Нет отзывов

Похожие инструкции для Hydrotech 485HE

Бренд: A.O. Smith Страницы: 56

Бренд: Air Delights Страницы: 7

Бренд: BENKISER Страницы: 13

Бренд: Delta Clean Страницы: 2

Бренд: Bradford White Страницы: 21

Бренд: lancer Страницы: 16

Tork Xpressnap H-4580

Бренд: U-Line Страницы: 2

Бренд: Oasis Страницы: 10

Бренд: Oasis Страницы: 2

Бренд: VOKERA Страницы: 19

Бренд: JW Страницы: 28

Бренд: Immergas Страницы: 32

Бренд: SPM Страницы: 68

Бренд: Everflo Страницы: 24

Бренд: IceManCooler Страницы: 2

Бренд: Rommelsbacher Страницы: 2

Бренд: Cillit Страницы: 20

PowerCiat LX HE

Бренд: CIAT Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды