Canature WaterGroup Hydrotech 485HE Скачать руководство пользователя

Страница: 9 / 36

Control Valve

Pressure Tank

Model 300 will get

an Adaptor and the

O-ring shown

Note: Tanks come

preloaded with media

with the exception of

some larger systems

where the media will

come in containers.

This is due to weight

restrictions. Media will

need to be loaded

on site. See steps to

properly load media

contained in this

manual.

,03257$17

3/($6((1685(7+($77$&+('

78%(67,))(1(5,6,16(57('

,1727+(%5,1(/,1(%()25(

7,*+7(1,1*

7+(187

There are 8 Red clips. Please

check to make sure you

have all of them.

Parts Box

60090003

2X 1” Straight

Adapter

60010006

Bypass Tool

60010026

O-Rings Attached

60090010

2 X 3/4”

Elbow

Adapter

60090026

Elbow, Inlet/Outlet, 1” NPT
Optional with some units

60010052

Transformer

92360

Grease

Packet

Brine Tank

(Round or

Square)

Brine Tank

Tubing

Brine Well/

Safety Float

Brine Tank Lid

Grid (Round or Square)

Grid Legs (3 for

Round and 4 for

Square)

Brine Tank Assembly (Round Brine Tank Shown))

,03257$17

3/($6((1685(7+($77$&+('

78%(67,))(1(5,6,16(57('

,1727+(%5,1(/,1(%()25(

7,*+7(1,1*

7+(187

Note: For upflow water softeners, a problem water injector

kit is enclosed. See Problem Water Injector Kit page for

usage information.

UNPACKING/INSPECTION

WARNING

RISK OF CHOKING

Discard all leftover parts and packaging materials after

installation. Small parts could be a choking hazard.

NOTE

Canature is NOT responsible for

damages in transit.

NOTE

Due to transportation and climatic conditions, all

connections, including the valve to the tank, need to

be checked at time of installation and hand

tightened, where necessary.

Be sure to check the entire unit for any shipping damage or parts loss. Also note damage to the shipping cartons. Contact the transportation

company for all damage and loss claims.

The manufacturer is not responsible for damages in transit

Small parts, needed to install the softener, are in a parts box. To avoid loss of the small parts, keep them in the parts bag until you are ready to

use them.

What is included in the box?

For Models 075,100,150, 200, 300 you will expect the following:

Control Valve*

Pressure Tank

Parts Box

Brine Tank Assembly

Drain Hose & Clamp (Not included in some brands)

Owners Manual

*All units (75, 100, 150, 200) are pre assembled with control

valve installed on the tank, no assembly required.

Содержание Hydrotech 485HE





































Результаты поиска

Содержание Hydrotech 485HE

Отзывы:

Похожие инструкции для Hydrotech 485HE

Бренды по названию

Популярные бренды

Canature WaterGroup Hydrotech 485HE, Руководство пользователя

Результаты поиска

Содержание Hydrotech 485HE

Отзывы:

Похожие инструкции для Hydrotech 485HE

Бренды по названию

Популярные бренды