Can-Am 2009 DS 450 Скачать руководство пользователя страница 114

Страница: 114 / 152

MAINTENANCE PROCEDURES

Check the following to keep the brakes
in a good operating condition:

– Brake fluid level
– Brake system for fluid leaks
– Brake for spongy feel
– Brake cleanliness
– Brake discs for excessive wear and

surface condition

– Brake pads for wear, damage or

looseness

– Front brake discs protector for dam-

age, replace if necessary.

SERVICE LIMITS

Brake pads thickness

1 mm

Discs thickness

3.5 mm

Maximum discs

warpage

0.2 mm

See your authorized Can-Am dealer if
a problem is detected concerning the
brake system.

WARNING

The brake fluid replacement or
brake system maintenance and
repairs should be performed by an
authorized Can-Am dealer.

Body

Vehicle Cleaning and Protection

Never use a high pressure washer to
clean the vehicle.

USE LOW PRES-

SURE ONLY (like a garden hose).

High pressure can cause electrical or
mechanical damages. Wrap-up muf-
fler tip to avoid water infiltration in the
exhaust system.

Painted parts which are damaged
should be properly repainted to pre-
vent rust.

When required, wash the body with
hot water and soap (only use mild de-
tergent). Apply non-abrasive wax.

NOTICE

Never clean plastic parts

with strong detergent, degreasing
agent, paint thinner, acetone, etc.

Seat Latch

Remove seat and check latch mecha-
nism. See an authorized Can-Am deal-
er for parts replacement if damaged.

Frame

Frame Inspection

Check frame for cracks or other dam-
age. See an authorized Can-Am dealer
for replace or repair.

Check fastener condition and tight-
ness on the vehicle. See an authorized
Can-Am dealer for torque specifica-
tions, parts replacement or repairs.

112

_____________________

Содержание 2009 DS 450

























































































































































Результаты поиска

Содержание 2009 DS 450

Отзывы:

Похожие инструкции для 2009 DS 450

Бренды по названию

Популярные бренды

Can-Am 2009 DS 450, Руководство оператора

Результаты поиска

Содержание 2009 DS 450

Отзывы:

Похожие инструкции для 2009 DS 450

Бренды по названию

Популярные бренды