Can-Am 2009 DS 450 Скачать руководство пользователя страница 106

Страница: 106 / 152

MAINTENANCE PROCEDURES

NOTICE

Never touch glass portion

of a halogen bulb with bare fingers,
it shortens its operating life. If glass
is touched, clean it with isopropyl al-
cohol which will not leave a film on
the bulb.

NOTE:

Concerning the following il-

lustrations, the headlight housing has
been removed from the vehicle for a
better comprehension.

To replace the headlight bulb, proceed
as follows.

Turn the ignition switch to OFF.

Remove rubber protector from head-
light housing.

vmo2008-018-038_a

TYPICAL

1. Rubber protector

Unplug connector from headlight.

Push the retaining clip round ends for-
ward then set them on the sides to un-
lock headlight bulb.

vmo2008-018-036_a

TYPICAL

1. Retaining clip

Lift and hold the retaining clip then re-
move the bulb.

vmo2008-018-037

TYPICAL

Properly reinstall removed parts in the
reverse order of their removal.

Check light operation.

Front Position Lamps Bulbs
Replacement

To replace the front position lamp bulb
located in the headlight housing, pro-
ceed as follows.

Turn the ignition switch to OFF.

Pull lamp socket out of headlight hous-
ing.

104

_____________________

Содержание 2009 DS 450

























































































































































Результаты поиска

Содержание 2009 DS 450

Отзывы:

Похожие инструкции для 2009 DS 450

Бренды по названию

Популярные бренды

Can-Am 2009 DS 450, Руководство оператора

Результаты поиска

Содержание 2009 DS 450

Отзывы:

Похожие инструкции для 2009 DS 450

Бренды по названию

Популярные бренды