manualshive.com logo in svg

CAMSO ATV R4S, Руководство пользователя

Поделиться
Скачать
CAMSO ATV R4S Скачать руководство пользователя страница 21

18

MAINTENANCE

•

Hub Bearing seal:

 The maintenance chart

recommends cleaning and lubricating the hub
seal. Refer to “Lubrication” in the 

Maintenance

section on page 20.

NOTE: Lubrication done at the recommended

intervals allows the hub seal to maintain
optimal sealing action and prolongs the life
span of the hub bearings.

•

Track Guide wear

: Check wear on Track

Guides. Replace guides if wear is too great.
Refer to “Wear” in the 

Maintenance

 section on

page 23.

•

Skate wear:

 Check wear of guide skates on

the Systems. Refer to “Wear” in the

Maintenance

 section on page 23. Replace if

wear is too great.

• Cracks

: Visually inspect the frames for

presence of cracks or defects that can impair
proper operation of the Track Systems.
Replace components if damaged. 

Sprockets

•

Wear

: Check wear of sprockets on the

Systems. Replace if wear is too great. Refer to
“Wear” in the 

Maintenance

 section on page 23. 

Anti-rotation

•

Lubrication

: The maintenance chart

recommends cleaning and lubricating the anti-
rotation arms. Refer to “Lubrication” in the

Maintenance

 section on page 21.

•

Bolt Torque

: Verify torque of assembly bolts

on anchor brackets and anti-rotation arms at
the recommended intervals specified by the
maintenance chart.

•

Cracked or bent parts

: Visually inspect anti-

rotation arms for presence of cracked or bent
parts that can impair proper functioning.
Replace components if damaged.

•

Rubber Dampers

: Verify condition of rubber

dampers on anti–rotation arms. Replace
dampers if they are deformed, cracked or show
severe wear. Refer to “Wear” in the

Maintenance

 section on page 21.

CAUTION: When pressure washing the Track
Systems, care must be taken to keep the water
stream away from wheel and hub bearing seals
and from rubber caps.

CAUTION: Hub bearings should be checked and
replaced in accordance with the maintenance
chart. Bearings that present abnormal play, make
noise or restrict rotation of hub are indications that
they must be replaced.

CAUTION: Use a breaker bar to remove the hub
assembly bolt. Do not use an air impact wrench. It
might cause the bolt to break.

CAUTION: Always replace washer and hub
assembly bolt when removing the hub from the
frame. Use new fasteners at reassembly.

SPECIAL TOOLING

Wheel Extractor

Camso Part Number: 2000-00-1050

Figure 33

Содержание ATV R4S



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды