Campbell NL241 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 76

background image

Table A-3: LED

State

Description

Red

double-flash

If the device is unsuccessful at joining or creating a network, the LED will
periodically double-flash red. The device will attempt to connect to the network
again after approximately one minute.

Fast red and

green flash

OS Download in progress – DO NOT DISCONNECT POWER

A.4 Power jumper

To prevent the NL241 from being powered over the CS I/O port, remove the two screws on the
top of the NL241, remove the NL241 top cover, remove the jumper above the mode button and
place it so that it is connected to only one post. With the jumper connected to only one post, the
NL241 can only be powered from the barrel connector. With the jumper connected to both posts,
the NL241 can be powered from the CS I/O port or from the barrel connector.

NL241 Wireless Network Link Interface

44

«
...
48
49
50
51
52
...
»

Содержание NL241













































































Отзывы:

Нет отзывов

Похожие инструкции для NL241

Бренд: YATEK Страницы: 72

Бренд: Jaga Страницы: 32

Бренд: IBC Страницы: 4

Бренд: Eurotops Страницы: 8

Бренд: KRATOS SAFETY Страницы: 36

Бренд: Mac Medical Страницы: 12

ELITE Ragley Pro Comfort

Бренд: Quest Leisure Products Страницы: 13

Бренд: KAM Страницы: 2

Бренд: Branch Manager Страницы: 28

Бренд: M-Audio Страницы: 40

LinidoSolutions LI2618.0006-12

Бренд: Handicare Страницы: 8

EPL-HB-150LED-RT-100-EPP

Бренд: Larson Electronics Страницы: 3

Бренд: Bowens Страницы: 4

Бренд: Geister Страницы: 28

Бренд: Schmalz Страницы: 36

Бренд: zitrek Страницы: 37

Бренд: Graco Страницы: 2

Бренд: Abilica Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды