manualshive.com logo in svg
background image

4

Operating Instructions

www.chpower.com

Important Safety Instructions

 

(Continued) 

Dropping or throwing the tool can result in 
damage that will make the tool unusable 
or unsafe. If the tool has been dropped or 
thrown, examine the tool closely for bent, 
cracked or broken parts and air leaks. STOP 
and repair before using or serious injury 
could occur.
 

Avoid using the  

  tool when the 

magazine is empty. Accelerated wear on the 
tool may occur.
 

Clean and check all  

  air supply hoses and 

fittings before connecting the tool to an air 
supply. Replace any damaged or worn hoses 
or fittings. Tool performance or durability 
may be reduced.

SeRvICe

a .  

Tool service must be performed only 
by qualified repair personnel. 

b .  

When servicing a tool, use only 
identical replacement parts. Use 
only authorized parts. 

c .   

Use only the lubricants supplied 
with the tool or specified by the 
manufacturer. 

 

Do not make any  

  modifications to the 

tool without first obtaining written approval 
from Campbell Hausfeld. Do not use the 
tool if any shields or guards are removed or 
altered. Do not use the tool as a hammer. 
Personal injury or tool damage may occur.
 

Disconnect air  

  supply and release 

tension from the pusher before attempting to 
clear jams because fasteners can be ejected 
from the front of the tool. Personal injury 
may occur.

aIR SOURCe

a .  

Never connect to an air source that 
is capable of exceeding 200 psi. 

Over pressurizing the tool is able 
to result in bursting, abnormal 
operation, breakage of the tool or 
serious injury to persons . Use only 
clean, dry, regulated compressed air 
at the rated pressure or within the 
rated pressure range as marked on 
the tool . Always verify prior to using 
the tool that the air source has been 
adjusted to the rated air pressure or 
within the rated air-pressure range . 

b .  

Never use oxygen, carbon dioxide, 
combustible gases or any bottled 
gas as an air source for the tool. 

Such gases are capable of explosion 
and serious injury to persons . 

Do not use any type of reactive 
gases, including, but not limited 
to, oxygen and combustible gases, 
as a power source. Use filtered, lubricated, 
regulated compressed air only. Use of a 
reactive gas instead of compressed air may 
cause the tool to explode which will cause 
death or serious personal injury.

Use only a pressure-regulated 
compressed air source to limit 
the air pressure supplied to the 
tool. The regulated pressure must not exceed 
120 psi. If the regulator fails, the pressure 
delivered to the tool must not exceed 200 psi. 
The tool could explode which will cause death 
or serious personal injury.

O

CO

2

120 psi

Save TheSe INSTRUCTIONS 

DO NOT DISCaRD

Operating The Tool

lUBRICaTION

This tool requires lubrication before 
using the tool for the first time and 
before each use . If an inline oiler is 
used, manual lubrication through the 
air inlet is not required on a daily basis .

 

The work surface 

  can become damaged 

by excessive lubrication. Proper lubrication is 
the owner’s responsibility. Failure to lubricate 
the tool properly will dramatically shorten 
the life of the tool and void the warranty.

1 .  Disconnect the air 

supply from the tool to 
add lubricant . 

2 .  Turn the tool so the 

air inlet is facing up . 
Place 4-5 drops of 30 
W non-detergent oil 
into air inlet . Do not 
use detergent oils, oil 
additives, or air tool 
oils . Air tool oils contain solvents 
which will damage the tool’s 
internal components .

3 .  After adding oil, run 

tool briefly . Wipe off 
any excess oil from the 
cap exhaust .

ReCOMMeNDeD 
hOOKUP

The illustration below shows the 
recommended hookup for the tool .

BUILT TO LAST

Recommended hookup

Quick Coupler

(Optional)

Quick Coupler

Air Hose

Oiler

Quick Plug 

(Optional)

Regulator

Filter

Содержание SB514000

































Отзывы: