Campbell Hausfeld AL2810, Инструкция по эксплуатации и каталог запасных частей

Страница: 3 / 32

Airless Paint Systems
3
Operating Instructions and Parts Manual
General Safety
Information
(Cont.)
4. Do not smoke or eat when spraying
paint, insecticides, or other
flammable substances.
5. Always work in a clean
environment. To avoid injury and
damage to the workpiece, do not
aim the spray gun at any dust or
debris.
6. When spraying and cleaning,
always follow the instructions and
safety precautions provided by the
material manufacturer (Refer to
MSDS).
GASOLINE ENGINE PRECAUTIONS:
●
Locate unit 25 feet away from
spray area in well-ventilated area.
●
NEVER operate in closed building
unless exhaust is piped outside.
●
NEVER allow hose to lay against
engine mufflers or hot parts.
●
NEVER refill fuel tank while engine
is hot or running.
SKIN INJECTION HAZARD:
●
High pressure spray
can inject toxins
into blood stream.
If injection occurs,
seek emergency medical treatment.
Use a face mask/respirator
and protective clothing
when spraying. Always
spray in a well ventilated
area to prevent health and fire
hazards. Refer to Material Safety Data
Sheets (MSDS) of spray material for
details.
●
Never try to stop leaks with any
part of your body.
!
WARNING
!
WARNING
!
WARNING
●
This system is capable of producing
3000 psi. Use only Campbell
Hausfeld replacement parts rated
at 3000 psi or higher.
●
Never spray without tip guard.
●
Ensure trigger lock is functioning
properly.
●
Always engage trigger lock when
not spraying.
●
Do not remove spray tip while
cleaning pump.
●
Never leave equipment pressurized
while unattended.
●
Do not clean spray tip while it is
attached to the spray gun. Remove
spray tip from gun to clean tip
guard.
●
Ensure tightness of high pressure
connections.
●
Do not use pliers to tighten or
loosen high pressure connections.
●
Motor is equipped with an automatic
thermal overload. Motor will restart
without warning, after cooling.
Never aim or
spray at yourself
or anyone else or serious injury could
occur.
FIRE OR EXPLOSION HAZARD:
●
Do not use solvents with flash
points less than 70°F (21°C) to clean
this equipment (examples of
acceptable cleaning solvents are
water, mineral spirits, lacquer
thinner, Xylene and high flash
napha. A partial example list of
unacceptable cleaning solvents are
low flash napha, mek, acetone,
alcohol and toluene).
Do not spray flammable
materials in vicinity of
open flame or near
ignition sources. Motors, electrical
equipment and controls can cause
!
WARNING
!
WARNING
!
WARNING
electrical arcs that will ignite a
flammable gas or vapor. Never store
flammable liquids or gases in the
vicinity of the unit.
Do not spray acids,
corrosive materials,
toxic chemicals, fertilizers or pesticides.
Using these materials could result in
death or serious injury.
!
WARNING
www.chpower.com
PRESSURE RELIEF PROCEDURE
Before servicing or resting unit,
relieve pressure from system by
following this procedure:
1. Engage gun trigger lock.
2. Turn off engine.
3. Disengage
gun trigger
lock and
trigger gun
to relieve
residual fluid
pressure. Hold metal part of gun
in contact with grounded metal
pail.
4. Re-engage gun trigger lock.
5. Turn
Prime/Pressure
Relief Valve to
open (priming)
position to
relieve fluid
pressure.
6. Leave
Prime/Pressure
Relief Valve OPEN until you are
ready to spray again.
NOTE: If spray tip or hose is clogged,
follow Step 1 to 5 above. Expect
paint splashing into the pail while
relieving pressure during Step 5. If
you suspect that pressure has not
been relieved after following the
above procedure, engage gun trigger
lock and take your unit to an
authorized Campbell Hausfeld
Service Center.
AL2810
OPEN POSITION