background image

Instructions - Parts List

RAZOR

®

 Siphon 

Feed Gun

II 2 G

TI8222A

312106F

ENG

A premier gun for the automotive refinish market for use with thin to medium viscosity 
materials (14-20 seconds Zahn #2 cup). If spraying heavier materials, use a pressure or 
gravity feed spray gun.

Includes HVLP, Compliant, and Conventional Series.

See page 2 for List of Models and maximum working pressures.
See page 10 for Parts.

This manual is available in the following languages.

Contents

Models  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Repair   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Technical Data   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Accessories   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Parts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Graco Standard Warranty   . . . . . . . . . . . . . . . . . . . 12

Graco Information   . . . . . . . . . . . . . . . . . . . . . . . . . 12

Important Safety Instructions

Read all warnings and instructions in this 
manual. Save these instructions.

English

312106

Spanish

312107

French

312108

German

312109

Italian

312110

Содержание RAZOR 2288588













Отзывы: