Camfil CleanSeal Exhaust V3 Скачать руководство пользователя страница 9

Страница: 9 / 63

EMC_SPEC040_CLCR.doc

Rev. E

–

2021 10 18

9/63

Install & Operating Manual

CleanSeal V3

Product Presentation

7.1

Design Features

CleanSeal housings are designed as terminal housings for air supply or extraction in clean rooms.

CleanSeal housings (CL) for ceiling installation are designed for supply air, but can perfectly work as
extract air terminals in the ceiling.

CleanSeal Exhaust housings (CR) for wall installation are designed for extract air.

Global Features

•

Fully welded design, including measurement ports

•

Tool-less filter clamping

•

Filter retainers (ceiling) / door stops (wall) for hands-free operation of clamps

•

Long lasting reliability and air tightness due to fully welded construction

•

Proven high corrosion protection against decontamination agents

•

Safe and fast locking / unlocking of front plates and doors

•

Installation by suspension ( only for ceiling installation) or compression

using removable “universal blocks”

•

Large choice of standardized sizes, materials, and inlet options

CleanSeal CL for Ceiling Installation

•

Available for PU filters (frame heights 66 / 78 / 90 / 110 mm)

•

Available for Gel filters (frame heights 71 / 105 / 115 mm)

•

Optional PRE filter (frame height 48 / 50 mm) for exhaust

(

❖

standard selection)

•

Full range of interchangeable front plates

•

Available with Manual Integrity Probe

(

❖

standard selection)

CleanSeal Exhaust CR for Wall Installation

•

Available for PU filters (frame heights 66 / 78 / 90 / 110 mm)

•

Available for Gel filters (frame heights 71 / 105 / 115 mm)

(

❖

custom option)

•

Optional prefilter (frame height 48 / 50 mm)

(

❖

standard selection)

•

Available as open-plenum version

•

Available with Manual Integrity Probe

(

❖

standard selection)

Содержание CleanSeal Exhaust V3
































































Результаты поиска

Содержание CleanSeal Exhaust V3

Отзывы:

Похожие инструкции для CleanSeal Exhaust V3

Бренды по названию

Популярные бренды

Camfil CleanSeal Exhaust V3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CleanSeal Exhaust V3

Отзывы:

Похожие инструкции для CleanSeal Exhaust V3

Бренды по названию

Популярные бренды