CAMERA LINK FC300ACL Скачать руководство пользователя страница 32

Страница: 32 / 36

N10316;32/36

- 32 -

11. Accessories

●

Camera Link cable (Optional)

[Type of conforming cable assembly]

Product name

Twin-Ax cable

Length of cable

Type

Maker

2 m

1MD26-3560-00C-200

3 m

1MD26-3560-00C-300

5 m

1MD26-3560-00C-500

(Note) The performance specifications are not guaranteed, if other components than the conforming cable above or the

products that we separately designate are used.

●

Tripod for FC

Tripod for FC300

300

300ACL (Optional)

ACL (Optional)

12. Notes

●

Do not disassemble the camera or alter the internal circuits. Accidents such as a fire may be caused by the heat generation

associated with failure in operation.

●

Refrain from connecting or disconnecting cables and connectors while power is being supplied.

●

Connect this equipment to a high quality power source unit that does not contain noise components.

●

A deliberate compatibility check of connector pin-out is required especially when using the power source other than that we

recommend.

●

Take appropriate measures to control the generation of noise if a power machine or other installations in the close

neighborhood of this equipment radiates noise, which might adversely affect this equipment

●

Do not use the camera in an environment subject to any temperatures other than that of the specifications or condensation or

on a place subject to considerable dust or constant vibration/impact.

●

When the camera is not used for a long time, isolate the power from the camera and remove the power cable and external

connection cables.

●

When an abnormal or failure condition is detected, immediately stop using this equipment, cut off the power supply, remove

the external connection cables and contact the dealer for inspection/repair.

●

Do not pull hard, twist, and roughly treat camera cable that is connecting camera and camera controller. It causes operation

error by cable breakage, fire caused by overheat, and failure of camera itself.

●

Do not expose the imaging area to excessively strong light source such as sun or laser source for a long time, otherwise

imaging device could be seized up and performance could be deteriorated.

●

Do not drop the camera or do not make an impact on it. It causes the camera to malfunction.

●

Do not adjust the portion other than that stated in this manual, otherwise It causes the failure.

●

Do not use this product for other than original purpose.

●

The specifications and operational details described in the catalogues, manuals and others are subject to change for

performance improvement or other reasons without notice.

Содержание FC300ACL





































Результаты поиска

Содержание FC300ACL

Отзывы:

Бренды по названию

Популярные бренды

CAMERA LINK FC300ACL, Инструкция по эксплуатации

Результаты поиска

Содержание FC300ACL

Отзывы:

Бренды по названию

Популярные бренды